background image

 

Settings Tab 
 

The Settings tab provides an interactive user interface for changing basic sensor settings with point and click 
operation. Consult the user manual for full software command details. 
 

 

Heater Settings: On/Off and Heater Setpoint 

 

Wind Speed & Direction Filter: On/Off and the averaging time period 

 

Heater Current Limit: Change the maximum current limit used by the sensor 

 

Wind Direction Datum Offset: Apply a directional offset to the sensor 

 

Please be aware that FT sensors can have different software versions and settings available. Some features may 
not be available for configuration. The key differences will be listed in the Appendix at the end of this document. 

 

 

Figure 7: Acu-Vis 2.0 Settings Display  

 

 

The ‘Sensor Warnings and History’ button will provide a history of the connected sensor settings where it 
has been connected to the PC

 

 

 

The  ‘Export  Sensor  Information’  button  creates  an  encrypted  file  containing  current  user  settings  and 
diagnostic  information.  This  feature  will  export  a  file  in  .fff  format  that  can  be  forwarded  to  the  FT 
Technologies support teams

 

 

 

The ‘Unlock Feature’ button is used to unlock advanced features in Acu-Vis 2.0, including the ‘Commands’ 
and the ‘User Calibration Table’ tabs. Contact FT Technologies for further details

 

Содержание FT702




















Отзывы: