Frymaster LOV M3000 Скачать руководство пользователя страница 27

Страница: 27 / 50

LOV

™

Generation II Technical Reference

Service Required Errors

SERVICE REQUIRED

error alternating with

YES

displays on the computer. After

YES

pressed the alarm is silenced. The computer displays an error message from the list below three
times with the location of the error. Then, the computer displays

SYSTEM ERROR FIXED?

YES/NO

. If

yes

is chosen, enter code

1111

. If

is chosen, the system returns to cook

mode for 15 minutes then redisplays error until issue is

xed.

Pressing the MIB reset button during any fi lter function will generate a

SERVICE RE-

QUIRED

error.

This is a list of the service required errors and cause.

ERROR MESSAGE

EXPLANATION

PUMP NOT FILLING

Oil not returning to vat quickly. Possible problems: dirty pad, bad
or missing O-rings, tripped or defective

lter pump, actuators or

linkage.

DRAIN VALVE NOT OPEN

Drain valve failed to open; the valve’s position is unknown.

DRAIN VALVE NOT CLOSED

Drain valve failed to close; the valve’s position is unknown.

RETURN VALVE NOT OPEN

Return valve failed to open; the valve’s position is unknown.

RETURN VALVE NOT CLOSED

Return valve failed to close; the valve’s position is unknown.

MIB BOARD

Problem with CAN communications; check for loose CAN connec-
tions. MIB board failure.

AIF BOARD

MIB detects AIF missing; AIF board failure.

ATO BOARD

MIB detects ATO board connection lost; ATO board failure.

HIGH LIMIT FAILURE

High limit circuit has an issue.

AIF PROBE

AIF RTD reading out of range.

ATO PROBE

ATO RTD reading out of range.

TEMP PROBE FAILURE

TEMP Probe reading out of range.

MIB SOFTWARE

Internal MIB software error.

INVALID CODE LOCATION

SD card removed during update.

MISCONFIGURED ENERGY
TYPE

Energy type in fryer setup is incorrect; set proper energy type gas
or electric. Press 1234 to enter setup to properly con

gure fryer.

RTC INVALID DATE

The date is invalid. Press 1234 to enter setup to properly con

ure fryer and set proper date.

Содержание LOV M3000



















































Результаты поиска

Содержание LOV M3000

Отзывы:

Frymaster LOV M3000, Техническое справочное руководство, Страница: 27 / 50

Результаты поиска

Содержание LOV M3000

Отзывы: