manualshive.com logo in svg

Fruitland RCF 1200, Эксплуатация и обслуживание

Поделиться
Скачать
Fruitland RCF 1200 Скачать руководство пользователя страница 26

26

Fruitland Manufacturing  •  

Toll Free: 1-800-663-9003  •  

www.fruitlandmanufacturing.com

Vane Replacement

Refer to pump rebuild video at:

 www.fruitlandmanufacturing.com

• 

Disconnect drive/power source from pump - Turn engine off !! Put Keys in your pocket !!

•  Drain oil from oil tank - inspect for debris & water
•  Remove oil tank cover by removing the hex bolts and aluminum sealing washers
•  Disconnect all oil lines and remove oil pump. (Held on by two bolts and lock washers).
•  Do not lose the oil pump coupling
•  Remove the seal housing by removing hex bolts and aluminum sealing washers
•  Remove the hex bolts and lock washers from the housing end cap
•  Slide the end cap off the rotor shaft.
•  The rotor bearing, shims, wave spring, & seals should be kept in order.
• 

Note their positioning if you remove the bevel springs/washers for replacement

• 

Remove old vanes and replace with new vanes that have been dipped/soaked in oil

•  Inspect housing bore, interior finish & bearings
•  We recommend replacing all seals and all related gaskets during this process
•  Reassemble in reverse order
• 

The housing end cap bolts should be tightened evenly to 22 ft./lbs. torque

• 

Fill oil tank with correct oil & hook up drive/power source

•  Resume Operations

Note:  

Special attention is to be given that the oil pump coupling is engaging the roll pin in the 

rotor shaft. Turn rotor by hand, it should turn freely.

*

Since there are many factors that cause rapid vane wear, we do not warranty vanes or 

any related damage from vanes worn beyond the recommended amount, unless a defect 

in material or workmanship caused the vanes to wear prematurely.

SERVICE NOTE

USE AUTHENTIC FRUITLAND PARTS ONLY!

If you have any questions, or require further information on installing, 

operating and or the maintenance of your vacuum pump contact:

 

1-800-663-9003 - [email protected] - [email protected]

Содержание RCF 1200

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды