Frontier SB1184 Скачать руководство пользователя страница 15

Страница: 15 / 52

ASSEMBLY

OM 0408SB1184-A

RACTOR

REPARATION

See Dealer for Tractor Preparation information.

NOWBLOWER

SSEMBLY

The snowblower is assembled at the factory however snowblower kits must be assembled. Use the
present manual and lay out all parts for assembly. Separate bolts and nuts into various sizes. After
assembly, torque all the bolts according to the

Torque Specification Table

at the end of manual.

Installation of SMV Sign

(Figures 1-2)

1. Figure

Remove the 1/4" NC x 1" bolt, the

flat washer and the 1/4" nylon insert nut
(items 1-2-3) that fixes the sign (item 4) to
the frame. Save the hardware.

2. Figure

Install the sign support (item 1) on

the snowblower with two 1/4" NC x 1" bolts,
two 1/4" flat washers and two 1/4" NC nylon
insert nuts (items 2-3-4).

3. Figure 2:

Using the hardware previously

removed, attach the SMV sign (item 5) with
two 1/4" NC x 1" bolts, two flat washers and
two 1/4" nylon insert nut (items 6-7-8).

Remove the black protective film from the
SMV sign.

Figure 1

Figure 2

Содержание SB1184




















































Результаты поиска

Содержание SB1184

Отзывы:

Бренды по названию

Популярные бренды

Frontier SB1184, Руководство оператора

Результаты поиска

Содержание SB1184

Отзывы:

Бренды по названию

Популярные бренды