background image

KEY P

AR

TS DIAGRAM

KEY PARTS DIAGRAM

Carriage Bolt M8

×

40 

×

4

A

B

C
D

E

1

.

Table

×

1

2

.

Workpiece Supports

×

2

3

.

Mounting Brackets 

×

2

4

.

Locking Knobs

×

2

6

Nut Locking Plate ×4
Flat Washer×4
Spring Washer

×

4

Nut

×

4

5

.

Locking Knobs with Bolt

×

2

8

OPERA

TING INSTRUCTIONS

Assembling the Saw Stand

Setting up the Saw Stand (see Fig. 1-2)

Preparing the Saw Stand

Operation

·

Do not overload the Saw Stand. Always observe the maximum load of the Saw Stand and the 

two table extensions.

·

Always hold the workpiece firmly, especially the longer and  heavier  section. After cutting 

through the workpiece, the centre of gravity may become dislocated in such an unfavourable 

manner that the saw stand tips over.

·

If possible, always place the workpiece on one or both workpiece supports.

WARNING

9

-

Carefully remove all parts included in 

the delivery from their packaging.

-

Remove all packaging material.

-   

Lay the saw stand upside down on the 

floor( legs facing upward).

-

Push the locking pin in and tilt the leg 

out-ward until the locking pin can be heard 

to engage.

-

Repeat this workstep with the other three 

legs.

-

Turn around the saw stand to the working 

position. The manufacturer logo must  face 

toward the front so that it can be read.

-

Ensure that the saw stand is stable and 

that all locking pins have engaged.

The saw stand is easily aligned with the 
height adjustable leg. 

-

Loosen lock nut  and screw the leg in or 

out until the saw stand is aligned level and 
all four legs face against the floor. 

Preparing the Mounting Brackets (see Fig. 4)

-

Place both Mounting Brackets on the saw 

stand in such a manner that the 

labelling can be read.

-

Hand-tighten  both locking handles. 

    

Extending the Saw Stand

-

Unplug the saw and lock the saw arm in the 

down position.

-

Lift one side of the saw and place a saw 

mounting bracket underneath, aligning 
the carriage bolts with the mitre saw mounting 

holes.

-

Lower the saw down onto the bracket, 

feeding the carriage bolts (A) through the 

mounting holes. Secure in place using a nut 
locking plate (B),then secure in place using a flat 

washer (C), spring washer (D), and nut (E).

-

Repeat steps to install second bracket to the 

other side of the saw.

-

After making sure both brackets are parallel 

to each other, finger tighten all four nuts (E) to 
hold in position.

(

See Fig.  6-7)

Long workpieces must be underlaid or support-

ed at their free end.

-

Place your long workpiece onto the saw table 

of the power tool.

-

Loosen locking knobs with bolt (5)  and pull 

the table extension  out to the desired clearance.

-

Retighten the locking knobs with bolt (5).

-

Loosen locking knobs  and adjust the height 

of the workpiece support  so that the workpiece 

rests level.
The workpiece must be positioned level on the 

power tool's saw table.

-

Retighten the locking knobs (4).

Mounting Workpiece Supports (see Fig. 3) 

-

Insert the workpiece support (2) into the 

table  extension. 

-

Tighten the locking knob 4 to lock the 

workpiece support.

-

Repeat the worksteps with the second 

workpiece support.

Fastening the Power Tool to the Mounting 

Brackets (see Fig. 5)

Model No.MSS507F  

Contact us: [email protected]

Отзывы: