Fronius TransSteel 3000c Pulse Скачать руководство пользователя страница 36

Страница: 36 / 140

Keylock

A keylock can be selected to prevent the settings from being inadvertently changed on
the control panel. As long as the keylock is active:
-

Settings cannot be adjusted on the control panel

Only parameter settings can be retrieved

Any assigned "Save" button can be retrieved provided that an assigned "Save" but-
ton was selected when the keylock was enabled

Activating/deactivating the keylock:

Keylock activated:
The message "CLO | SEd" appears on the
displays.

Keylock deactivated:
The message "OP | En" appears on the
displays.

The keylock can also be activated and deactivated using the keylock switch option.

Содержание TransSteel 3000c Pulse













































































































































Результаты поиска

Содержание TransSteel 3000c Pulse

Отзывы:

Похожие инструкции для TransSteel 3000c Pulse

Бренды по названию

Популярные бренды

Fronius TransSteel 3000c Pulse, Руководство по эксплуатации

Результаты поиска

Содержание TransSteel 3000c Pulse

Отзывы:

Похожие инструкции для TransSteel 3000c Pulse

Бренды по названию

Популярные бренды