Fronius 4,044,008 Скачать руководство пользователя страница 71

Страница: 71 / 136

Safety

Determining the
TCP of the weld-
ing torch, deter-
mining the X-axis
and Y-axis of the
torch body
changeover sta-
tion

Screw 3 TCP tips into the holes (1) of
the rack holder
Measure TCP of the welding torch
being used
Determine the X-axis and Y-axis of the
torch body changeover station using
the TCP tips and record in the coordi-
nate system of the robot

Fitting the robot
programming aid

When carrying out the following work, position the robot arm and the torch body cou-
pling so that

the Unlock/Lock button on the torch body changeover station can be pressed with
one hand

the torch body can be placed onto or removed from the torch body coupling with
the other hand

Hold the torch body on the robot arm with one hand

CAUTION!

Risk of injury from escaping compressed air and flying parts from the

torch body coupling. During the activities described below, always wear the fol-
lowing protective equipment:
-

ear protection

protective goggles with side protection

gloves - electrically insulated and providing protection against heat

CAUTION!

Risk of injury from razor-sharp TCP tips. Do not touch the pointed end

of the TCP tips.

(1)

CAUTION!

Risk of injury from razor-sharp TCP tips and tip of robot programming

aid. Do not touch the pointed end of the TCP tips and the robot programming aid.

Содержание 4,044,008









































































































































Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды

Fronius 4,044,008, Руководство по эксплуатации

Результаты поиска

Содержание 4,044,008

Отзывы:

Похожие инструкции для 4,044,008

Бренды по названию

Популярные бренды