Fronius 4,044,008 Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 136

background image

122

Replacing the torch body sensor

Preparation

Depressurise the compressed air line of the torch body changeover station and make
sure that this compressed air line remains depressurised for the duration of the work
on the device
Disconnect the compressed air line from compressed air connection "A" on the torch
body changeover station

Press and hold the Unlock/Lock button on the torch body changeover station until
compressed air no longer emerges from compressed air connection "A" on the torch
body changeover station

-

compressed-air booster unit in the torch body changeover station discharges

De-energise the torch body changeover station

Safety

Removing the old
torch body sen-
sor

Undo the 8 screws (1)
Remove lid (2)

CAUTION!

Risk of injury from escaping compressed air from compressed air

connection "A". Compressed air emerges at up to 16 bar (232.06 psi) from com-
pressed air connection "A" when the Unlock/Lock button is pressed. While com-
pressed air is emerging from compressed air connection "A":
-

wear ear protection

-

keep the face and all other body parts away from compressed air connection
"A"

-

ensure that no other persons are in the vicinity of the torch body changeover
station

1

2

3

4

CAUTION!

Risk of injury from compressed air escaping unintentionally. The torch

body changeover station must remain depressurised and de-energised until all
work is completed.

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(2)

1

2

«
...
120
121
122
123
124
...
»

Содержание 4,044,008









































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4,044,008

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: YOKOGAWA Страницы: 12

Бренд: Vello Страницы: 12

Бренд: BAFANG Страницы: 4

Бренд: Q-See Страницы: 28

Q.HOME+ ESS HYB G2

Бренд: Qcells Страницы: 2

Бренд: NEEWER Страницы: 58

Reference Series

Бренд: OEM Audio Страницы: 29

Бренд: XCM Страницы: 11

Бренд: BabySense Страницы: 76

Бренд: Warrior Products Страницы: 4

WirelessAIR 73000EZ

Бренд: Air Lift Страницы: 12

Бренд: ergobaby Страницы: 8

Бренд: DrBrowns Страницы: 2

Бренд: ESAB Страницы: 12

Бренд: Orno Страницы: 4

Monitor _QSG_DE01

Бренд: M-Audio Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды