Fritsch ANALYSETTE 22 NeXT Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 56

background image

8

Cleaning

8.1 Cleaning the devices

DANGER!
Mains voltage!
– Before beginning with cleaning work, disconnect

the mains plug and protect the device against being

unintentionally switched back on!

– Do not allow any liquids to flow into the device.
– Indicate cleaning work with warning signs.
– Put safety equipment back into operation after

cleaning work.

The devices can be cleaned using a moist cloth or the supplied microfibre

cloth.

8.2 Cleaning the hoses

You can clean stubborn soiling in the hoses of the wet dispersion unit by

adding the included cleaning powder.
Proceed as follows for cleaning the hoses:
1.

Empty the sample bath.

2.

Remove the hoses on the measuring cell drawer and connect both

hoses with the supplied connector. This creates a new liquid circu-

lation system.

3.

Fill the sample bath with liquid.

4.

Set the pump power to maximum and add 10 ml of cleaning

powder to the sample bath.

5.

Let the pump run for about 2 minutes. Then rinse the system 2 - 3

times to rinse out all the cleaning powder.

Cleaning

- 37 -

«
...
35
36
37
38
39
...
»

Содержание ANALYSETTE 22 NeXT

























































Отзывы:

Нет отзывов

Похожие инструкции для ANALYSETTE 22 NeXT

Бренд: Laica Страницы: 4

Бренд: ParaBody Страницы: 4

Бренд: ACDC Страницы: 4

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Rapala Страницы: 14

Бренд: S.R.Smith Страницы: 43

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Waterpik Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды