Fristam Pumps FPM 3531 Скачать руководство пользователя страница 15

Страница: 15 / 25

9.4

Changing the motor

1. Turn off the motor and prevent it from being able to be

turned on accidentally.

2. Remove the pump head. See

Chapter

9.6 "Pump Head Remov-

al", Page

3. Take the lantern off of the motor.

4. Remove the flanged shaft with outside motor from the mo-

tor shaft.

5. Replace the motor.

6. Install and tighten flanged shaft with outside motor onto

the motor shaft.

7. Attach the lantern onto the motor.

8. Mount the pump head. See

Chapter

9.8 "Mounting the pump

head", Page

9.5

Replacing the magnetic coupling

NOTE

It is highly recommended to use

Fristam

for maintenance pur-

poses or when replacing the magnetic coupling.

Note: The installation instructions for the magnetic coupling can be
found in the magnetic coupling operating manual. In the manual
can be found in the enclosed documents.

1. Disassembling the pump head, see

2. Disassemble the magnetic coupling, see

Magnetic coupling

operating manual

in the enclosed documents.

3. Replace the magnetic coupling.

4. Pre-assemble the magnetic coupling, see

Magnetic cou-

pling operating manual

in the enclosed document.

5. Apply Loctite 243 to all threaded connections. If the quality

and properties of another brand adhesive are equivalent,
this product may be used.

6. Tighten the attachment on the pump shaft, see

Table

"Tightening torques of screws/motor shaft"

, this will fix

the magnetic coupling in place.

7. Attach the, contaminant shell, see

Magnetic coupling oper-

ating manual

in the enclosed document.

8. Assemble the pump head, see

Chapter

9.8 "Mounting the

pump head", Page

9. Check the clearance, see

Chapter

9.7 "Checking of the Clear-

ances", Page

9.6

Pump Head Removal

Preparation

1. Turn off the motor and prevent it from being able to be

turned on accidentally.

2. Close the valve in the pressure line.

3. Close the valve in the discharge line.

4. Completely empty the pump.

5. Loosen the suction and discharge connections.

6. Take the pump out of the system.

Procedure

Fig.

Pump

cover

1. Loosen nuts

(25)

on pump cover.

2. Remove the nuts, washers, pump cover

(26)

and cover seal

(27)

Note for model FSM35, etc.: If the cover can not be loosened
easily, slightly tap the cover, using a plastic hammer (mallet).

Thread

Tightening torques

M10

M12

M16

135

Table

Tightening torques of screws/motor shaft

Thread

Tightening torques

M10

M12

M16

135

Table

Tightening torques of screws/motor shaft

Содержание FPM 3531


























Результаты поиска

Содержание FPM 3531

Отзывы:

Fristam Pumps FPM 3531, Английский перевод оригинального немецкого руководства по эксплуатации, Страница: 15 / 25

Результаты поиска

Содержание FPM 3531

Отзывы: