9
WATER DISPENSER & ICE SERVICE (CONTINUED)
PureSource
TM
* ICE AND WATER FILTER (some models)
System Startup:
Water supply does not need to be turned off, however, do not use ice and water dispenser while installing filter. The filter
cartridge has already been installed in the filter housing at the factory. Refer to the
How to Prime the Water Supply System
section to properly fill the system with water.
Order new filter cartridges through the dealer where you bought the refrigerator, contact the
Electrolux Solutions Hotline at 1-800-944-9044, or go to our web site at www.frigidaire.com. It
might be good to order some filter cartridges when you first install your refrigerator. Be sure to
ask for
the RG-100 PureSource™* replacement cartridge.
The
PureSource™ * NGRG-
2000 Ice and Water Filter
System with the RG-100
cartridge is tested and
certified by NSF International,
the nationally recognized and respected,
not for profit, certification organization for
public health safety. The
PureSource™*
system is tested and certified to ANSI/NSF
Standard 42. See performance data sheet
for specifications. This system should not
be used on water that is microbiologically
unsafe or with water of unknown quality
unless the water has been adequately
disinfected before or after traveling through
the filtration system.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
Changing the Filter:
Water conditions vary throughout the world, but changing the water filter every
6 - 9 months normally will ensure the highest possible water quality.
Ice jams in
the ice maker and/or hollow ice cubes (partially frozen cubes with water
inside), may also be a sign that your water filter needs changing.
If the filter has
been in a refrigerator that has not been in use for awhile (during moving for
example), change the filter before reinstalling the refrigerator. The dispenser
system will also operate without filtration (with filter cartridge removed).
To change filter:
It is not necessary to turn the water supply off to change the filter.
1.
Set ice maker wire signal arm to the OFF (up) position. Turn dispenser lock to
the locked position.
2.
Hold filter cup firmly, and unscrew towards left (Some water could leak out as
you remove cup. This is normal.). Filter cartridge should come down with cup.
If cartridge remains in housing, pull down gently, while twisting filter back and
forth.
3.
Rinse out cup under running water.
4.
The large o-ring that seals the filter system sets in the o-ring groove
down inside the cup. Should the o-ring fall out during filter cartridge
replacement, simply place it back in the groove prior to screwing the cup
back in place. If the o-ring becomes damaged, you will need to order one
from the
Electrolux Solutions Hotline.
5.
Discard old filter cartridge.
6.
Remove new filter cartridge from packaging and place in cup. The end
with the small o-ring should be up, out of the cup.
7.
Screw cup, with filter, back onto housing.
Do Not Use Wrench To Reinstall
Cup
. Filter cartridge will self-align as cup is tightened. Be sure cup is
completely tightened with
PureSource™
logo facing outward.
Do Not
Tighten Past Stop.
8.
Set ice maker wire signal arm to the ON (down) position.
9.
Check for leaks. Open refrigerator door. Wipe any water droplets from the
filter cup. Unlock the dispenser lock. Fill a glass with water. If there is a leak,
unscrew filter cup, and reinsert the filter cartridge. Check placement of large
O-ring. Reinstall filter cup, making certain it is tightened completely.
10. To prime filter system and purge air from water line, continue flushing the
system for approximately 3 minutes to assure that the purest water possible is
stored in the water tank. There will be noticeable spurts and sputters as the
system pushes air out through the system and out the dispensing spout. This
is normal.
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter
FIL
FIL
FIL
FIL
FILTER REPLA
TER REPLA
TER REPLA
TER REPLA
TER REPLACEMENT REMINDER STICKERS
CEMENT REMINDER STICKERS
CEMENT REMINDER STICKERS
CEMENT REMINDER STICKERS
CEMENT REMINDER STICKERS
There is a set of Reminder Stickers included in the envelope that the Use & Care Guide came in. Choose a dated sticker that
indicates 6 - 9 months (depending on your water quality and usage) from the date of installation. Place the sticker on the front
