background image

31

STORAGE FEATURES

CAUTION

To avoid personal injury or property 

damage, handle tempered glass shelves 

carefully. Shelves may break suddenly 

if nicked, scratched, or exposed to 

sudden temperature change. Allow 

the glass shelves to stabilize to room 

temperature before cleaning. Do not 

wash in dishwasher.

You can easily adjust shelf positions in 

the refrigerator compartments to suit 

your needs. The shelves have mounting 

brackets that attach to slotted supports 

at the rear of each compartment.

IMPORTANT

Be aware of the air seal located at the rear 

of the shelf. Shelves located on the left 

side should have the air seal mounted on 

the far left side. Shelves located on the 

right side should have the air seal mount-

ed on the far right side. This is to ensure 

there is no interference with the large air 

tower on the back wall of the cabinet. This 

also applies to the crisper shelves.

Change the Position of a Shelf

1.  Remove all food from shelf.
2.  Lift the front edge up and pull the 

shelf out.

Reposition the Air Seal

For glass shelves:

1.  Remove air seal by pushing seal 

straight back.

2.  Position the air seal towards the 

outside edge of the shelf to avoid the 

air tower when shelf is pushed back 

into place.

3.  Install seal by sliding the open channel 

end of the seal onto back edge of 

shelf until seal sits snug on back 

of shelf and flap sits at about a 10 

degree angle from shelf surface.

Shelves

3.  Replace by inserting the mounting 

bracket hooks into the desired 

support slots.

4.  Lower the shelf and lock into position.

Содержание FRFC2323AS



















































Отзывы: