Specifications
subject to change.
Specifications
subject to change.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FFTW1001P
10/13
© 2013 Electrolux Home Products, Inc.
Top Load Washer
FFTW1001PW
3.4 Cu. Ft. D.O.E.
Top Load Washer Specifications
•
Product Shipping Weight (approx.) – 118 Lbs.
•
An electrical supply with grounded three-prong receptacle is required.
The power supply circuit must be installed in accordance with current
edition of National Electrical Code (ANSI/NFPA 70) and local codes &
ordinances.
(Do not use same circuit as dryer.)
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Amps @ 120 Volts = 8.0 Amps
•
Equipped with 120V 3-wire power supply cord, approx. 60" long.
•
Always consult local and national electric & plumbing codes.
•
To maximize detergent effectiveness, ambient temperature should
never be below 60° F.
•
Washer can be installed in recess or closet requiring 0" minimum
installation clearance around sides and back of unit. To achieve
0" minimum rear clearance when installed with dryer, dryer MUST
be vented straight back. Closet installation requires additional 1"
minimum clearance between front of unit and door. If washer and
dryer are installed in same closet, door MUST be vented with 120 sq. in.
minimum louvered opening, equally divided, located 3" from top and
bottom of door. A louvered door with equivalent air openings for full-
length of door is acceptable. Air openings MUST remain unobstructed
with door installed.
(For additional installation details, refer to Product
Installation Guide on web.)
•
Do NOT install in area exposed to dripping water or outdoor weather
conditions; or where gasoline or other flammables, including
automobiles, are kept or stored.
•
Floor MUST be solid with 1" maximum slope. To minimize vibration
or movement, reinforcement of floor may be necessary. Do NOT
install on carpeted surface.
•
Leveling legs supplied to level unit properly and reduce excessive
noise and vibration.
•
H/C water faucets MUST be installed within 42" of washer’s water
inlet and MUST be 3/4" with threading for laundry hose connection
to connect to 48" inlet hoses.
•
Water pressure MUST be between 30 and 120 psi with NOT more
than 10 psi pressure difference between hot and cold.
•
Drain standpipe requires diameter of 1-1/4" min. and height of
36" min. / 96" max. above floor, capable of eliminating 17 gallons
per minute. Attached 61" drain hose can reach 74"-high standpipe.
For higher standpipe, optional Drain Hose Extension Kit available.
•
For manufactured or mobile home installation optional Mobile Home
Installation Kit (PN # 137067200) required.
(For specific installation
details, refer to Product Installation Guide on web.)
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
•
Mobile Home Installation Kit – (PN # 137067200).
•
Drain Hose Extension Kit – (PN # 137098000).
Top Load Laundry - Washers
Frigidaire Baseline (P Model)
Recess or Closet Installation
Washer requires 0" minimum installation clearance
around sides and back of unit. To achieve 0" minimum
rear clearance when installed with dryer, dryer MUST
be vented straight back. Closet installation requires
additional 1" minimum clearance between front of unit
and door. If washer and dryer are installed in same
closet, door MUST be vented with 120 sq. in. minimum
louvered opening, equally divided, located 3" from top
and bottom of door. A louvered door with equivalent
air openings for full-length of door is acceptable.
Air openings MUST remain unobstructed with door
installed. For additional installation details, refer to
Product Installation Guide(s) on web.
Front
H/C Water
inlets
(rear) -
48" hose
length
42
1
/
2
"
60"
Power
cord
(rear)
38
1
/
2
"
27"
Drain
hose
retention
clamp
(rear)
61" Hose
length
beyond
clamp
Side
59"
29"
0"
min.
0"
min.
20
1
/
2
"
min.
Front
Vented door
0" min.
1" min.
Side
60"
sq. in.
min.
3"
60"
sq. in.
min.
3"
