Frigidaire FFHT1832TE Скачать руководство пользователя страница 12

12

CONNECTING THE WATER SUPPLY

WARNING

To avoid electric shock, which can cause 

death or severe personal injury, disconnect 

the refrigerator from electrical power before 

connecting a water supply line to the 

refrigerator.

CAUTION

To Avoid Property Damage:

•  Copper or Stainless Steel braided tubing 

is recommended for the water supply 

line. Water supply tubing made of ¼ 

inch plastic is not recommended to be 

used. Plastic tubing greatly increases 

the potential for water leaks, and the 

manufacturer will not be responsible for 

any damage if plastic tubing is used for 

the supply line.

•  DO NOT install water supply tubing in 

areas where temperatures fall below 

freezing.

•  Chemicals from a malfunctioning softener 

can damage the ice maker. If the ice 

maker is connected to soft water, ensure 

that the softener is maintained and 

working properly.

IMPORTANT

Ensure that your water supply line 

connections comply with all local plumbing 

codes.

NOTE

Check with your local building authority 

for recommendations on water lines and 

associated materials prior to installing your 

new refrigerator. Depending on your local/

state building codes, Frigidaire recommends 

for homes with existing valves its 

Smart 

Choice

®

 water line kit 5305513409 (with 

a 6 ft. Stainless Steel Water Line) and for 

homes without an existing valve, Frigidaire 

recommends its 

Smart Choice

®

 water line 

kit 5305510264 (with a 20 ft. Copper Water 

Line with self-tapping saddle valve). Please 

refer to www.frigidaire.com/store for more 

information.

Before Installing The Water Supply Line, 

You Will Need:

• 

Basic Tools: adjustable wrench, flat-blade 

screwdriver, and Phillips

TM

 screwdriver

•  Access to a household cold water line with 

water pressure between 30 and 100 psi.

•  A water supply line made of ¼ inch (6.4 

mm) OD, copper or stainless steel tubing. 

To determine the length of tubing needed, 

measure the distance from the ice maker 

inlet valve at the back of the refrigerator 

to your cold water pipe. Then add 

approximately 7 feet (2.1 meters), so the 

refrigerator can be moved out for cleaning 

(as shown).

•  A shutoff valve to connect the water supply 

line to your household water system. DO 

NOT use a self-piercing type shutoff valve.

• 

Do not re-use compression fitting or use 

thread seal tape.

•  A compression nut and ferrule (sleeve) for 

connecting a copper water supply line to 

the ice maker inlet valve.

Содержание FFHT1832TE
























Отзывы: