Frigidaire FFHB2740PP страница 25 Скачать руководство пользователя

Страница: 25 / 33

CHANGING THE FILTER

Locating the Filters

Your refrigerator is equipped with water filtering system.

The water filter system filters all dispensed drinking

water, as well as the water used to produce ice.

Water Filter

The water filter is located at the top right side of the

fresh food compartment.

Ordering Replacement Filters

To order your replacement filters, please visit our online

store at www.frigidaire.com/store, by calling toll-free

at 877-808-4195, or by visiting the dealer where you

purchased your refrigerator. Frigidaire recommends

that you order extra filters when you first install your

refrigerator, and that you replace your filters at least once

every six months.
Here is the product number to request when ordering:
PureSource Ultra

Water Filter

Part #ULTRAWF

Replacing the Water Filter

In general, you should change the water filter every six

months to ensure the highest possible water quality.

Water Filter Status on the user interface prompts you

to replace the filter after a standard amount of water

(200 gallons/757 liters for PureSource Ultra

)

has

flowed through the system.

If your refrigerator has not been used for a period of time

(during moving for example), change the filter before

reinstalling the refrigerator.

Filter Cartridge

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Test & certification results:

•

Rated Capacity - 200 gallons/757 liters for

PureSource Ultra

ice and water filter

• Rated service flow - .50 gallons per minute
•

Operating Temp: Min. 33°F, Max. 100°F

•

Maximum Rated Pressure - 100 pounds per square inch

•

Recommended Minimum Operating Pressure:

30 pounds per square inch

To replace your PureSource Ultra

water filter:

It is not necessary to turn the water supply off to change

the filter. Be ready to wipe up any small amounts of water

released during the filter replacement.

1 Turn Off the ice maker power switch.
2

Remove the filter by pushing on the end/face of the filter.

Slide the old water filter cartridge straight out of the

housing and discard it.

Unpackage the new filter cartridge. Using the

alignment guide, slide it gently into the filter housing

until it stops against the snap-in connector at the

back of the housing.

5 Push firmly until the cartridge snaps into

place (you should hear a click as the cartridge

engages the snap-in connector).

6 Press a drinking glass against the water dispenser

while checking for any leaks at the filter housing.

Any spurts and sputters that occur as the system

purges air out of the dispenser system are normal.

After filling one glass of water, continue flushing the

system for about four minutes.

8 Turn On the ice maker.
9 Press and hold the Water Filter

button on the Ice

& Water Dispenser control panel for three seconds.

When the display changes from Red to Green, the

status has been reset.

The PureSource Ultra

ice and water filter

system is tested and certified to NSF/ANSI

Standards 42 and 53 for the reduction of claims

specified on the performance data sheet.

More about your Advanced Water Filter



NOTE

When ordering your replacement filter, please reorder

the same filter type that is currently in your refrigerator.

Содержание FFHB2740PP


































Результаты поиска

Содержание FFHB2740PP

Отзывы:

Похожие инструкции для FFHB2740PP

Бренды по названию

Популярные бренды

Frigidaire FFHB2740PP, Инструкция по использованию и уходу

Результаты поиска

Содержание FFHB2740PP

Отзывы:

Похожие инструкции для FFHB2740PP

Бренды по названию

Популярные бренды