background image

10

Radiant surface elements may appear to have cooled

after they have been turned off. 

The glass surface may

still be hot

 and burns may occur if the glass surface is

touched before it has cooled sufficiently.

Do not place flammable items 

such as plastic salt and

pepper shakers, spoon holders or plastic wrappings on

top of the range when it is in use.

 

These items could melt

or ignite. Potholders, towels or wooden spoons could

catch fire if placed too close to the surface elements.

CAUTION

Heating with inner (small)

element only

Heating with both

elements

Fig. 1

Fig. 2

Dual radiant surface elements 

(some models)

Symbols on the backguard are used to indicate which coil of
the dual radiant element will heat. The   symbol indicates
the inner coil only. The   symbol indicates both inner and

outer coils will heat.

You may switch from either coil setting at any time during

cooking.

 

 See 

Suggested radiant surface element

settings table

 on previous page.

To operate a dual radiant element:

1. Place correctly sized cookware on dual radiant surface

element.

2. Push in and turn the surface control knob clockwise to

begin heating both the inner and outer portions of the

dual element. If only the inner heating portion is

needed like for smaller cookware, push in and turn the

knob counter-clockwise to start.

3. When cooking is complete, turn the dual radiant surface

element OFF before removing the cookware.

Areas that heat are shown

darkened.

Start most cooking operations on a higher setting and then

turn to a lower setting to finish cooking. The surface control

knobs do not have to be set exactly on a particular mark.

Use the marks as a guide and adjust the control knob as

needed.  A glowing red surface heating area extending

beyond the bottom edge of the cookware indicates the

cookware is 

too small

 for the surface heating area.

The size and type of utensil used, and the amount and

type of food being cooked will influence the setting

needed for best cooking results.

NOTES

IMPORTANT

Do not allow aluminum foil, or ANY material that can

melt to make contact with the ceramic glass cooktop.

If these items melt on the cooktop they will damage the

ceramic cooktop.

SETTING SURFACE CONTROLS

The 

on

 indicator light will glow when one or more

elements are turned ON. A quick glance at this indicator

light when cooking is finished is an easy check to be sure

all control knobs are turned OFF. The 

hot surface

indicator light will continue to glow AFTER the control

knob is turned to the “OFF” position and will glow until

the heating surface area has cooled sufficiently.

Содержание FFEF3013L M

























Отзывы: