background image

4

HANDLE

This wall oven can easily be modified to a left or a right
hand door opening.  It is preferable to reverse door
opening prior to the installation of the wall oven into
the cabinet cavity.  If wall oven is already installed,
remove the 4 lateral screws securing it against the
cabinet, then pull wall oven outward by approx. 50 mm
(2”).

Two of the lateral screws are located at the low end of
upper grille; the other 2 screws hold the lower grille in
place.

Tools required: Philips #2 and

Robertson #2 screwdrivers

DOOR REVERSAL PROCEDURE

(see figure 6)

  1. Pull the door open.

  2. While supporting the door with one hand, remove

the 2 screws securing top hinge #1 to the door.
Remove the top hinge, then lift up the door such as
to clear the lower hinge pin and remove the door.

  3. Lay the door on a table protected by a blanket; the

inner door surface must face toward you.

  4. Remove the 2 screws which secure the handle;

remove the handle.  Remove filler plates #2, #3, and
#12 using a flat blade tool.

  5. Reassemble upper hinge #1 at the lower end and on

the opposite side of the door.

  6. Remove lower hinge #4.  Relocate the nylon washer

on the lower hinge pin.

  7. Remove screws securing the top and bottom door

trims #5 and #6 to the door; remove these trims.

  8. Slide the glass panel flush with the edge of the

enamelled steel inner door (toward the new handle
location).

  9. Invert position of trims #5 and #6 (trim #5 at the

bottom and trim #6 at the top); reassemble trims.

10. Reassemble the handle and filler plates #2, #3 and

#12 on the opposite side of the door.

11. Remove and relocate the filler plates #7 on the

opposite side of the oven frame.

12. Remove the latch pin #10 and relocate latch on the

opposite side of the oven door.

13. Invert positions of #8 and #9 hinge fixed parts

(ex. from top left side to bottom right side).

14. Reassemble the door onto the wall oven; insert

door into the fixed lower hinge, then proceed with
the reassembly of the upper hinge.  Align door by
using available play in the hinge holes.

FIGURE 6

4

DOOR REVERSING

Содержание FEB702CESG









Отзывы: