background image

7

PERFORMANCE

EVAPORATOR AIR

OPERATING

ELECTRICAL

R-22

COMP.

DATA*

TEMP. °F.

PRESSURES

RATINGS

REFRIG.

OIL

Cooling

DISCHARGE

TEMP.

SUCTION

DISCHARGE

AMPS

LOCKED

CHARGE IN

CHARGE IN

AIR

DROP °F

ROTOR AMPS

OZ.

FLUID OZ.

**SQ05J10A-1

55.45

24.55

76.5

281

4.4

34.0

16.0 R-22

9.8

**SQ06J10A-1

51.45

28.55

75.5

262

5.2

35.0

15.7 R-22

9.8

**SQ07J10A-1

50.41

29.59

75.5

277

6.5

40.0

24.0 R-22

9.8

**SQ08J10AB-1

50.50

29.50

74.5

262

7.5

39.2

19.5 R-22

9.8

* Rating Conditions:80°F Room Air Temperature and 50% Relative Humidity with

95°F Outside Air Temperature at 40% Relative Humidity.

** Use Sunisco 4GDID Refrigerant Oil or Atmos 60.

SPECIFICATIONS

SQ05J10A-1 SQO6J10A-1 SQO7J10A-1 SQO8J10AB-1

BTUH (Cooling)

5400

6300

7100

8000

E.E.R. (Cooling)

11.0

10.8

10.3

10.0

Volts

115

115

115

115

Amperes (Cooling)

4.4

5.2

6.5

7.5

Total Watts (Cooling)

490

585

690

800

Hertz

60

60

60

60

Fuse / Breaker Size

15

15

15

15

Fan RPM

1115

1115

1115

1115

Evaporator Air CFM

160

160

140

165

Exhaust Air CFM

Yes

Yes

Yes

Yes

Dehumidification Pts / Hr.

1.5

2.0

2.5

2.5

Width

19¾

19¾

19¾

19¾

Height

14"

14"

14"

14"

Depth

21

3

/

8

21

3

/

8

21

3

/

8

21

3

/

8

Minimum Ext. into Room

Minimum Ext. to Outside

10¾

10¾

10¾

10¾

Net Weight (Lbs.)

76

78

79

82

Shipping Weight (Lbs.)

81

83

84

87

Unit Performance Sheets

Содержание SM21J30A4







































































Отзывы: