Friedrich Kuhl KCQ06A10A Скачать руководство пользователя страница 59

Страница: 59 / 78

FAULT

CODE

PROBLEM

CONTROL BOARD'S ACTION

Front Panel Button Stuck For More

Than 20 Seconds

Continue to monitor for "OPEN" (Unstuck) switch. Do not process

switch input. ENSURE FRONT COVER DOES NOT DEPRESS

BUTTONS

Indoor Temperature Sensor is Open

or Shorted

Set temp to 75°F in COOLING or 68°F in HEATING. Unit continues

to operate

Indoor Coil Temperature Sensor is

Open or Shorted

Control Board sets temp to a default of 40°F. Override sensor.

Unit continues to operate.

Outdoor Coil Temperature Sensor is

Open or Shorted

Sets temp to 20°F. Override sensor. Continue operation. Use Elec

Heat if available for HEATING. If not available use HEAT PUMP if

outdoor temp allows.

Outdoor Coil > (greater than) 175 F

Shut down for 5 min.

Indoor Coil < (less than) 30 F for 2

consecutive minutes

Turn compressor off. When coil temp reachs 45°F resume

operation after lockout time.

Unit Cycles > (grater than) 9 Times

per hour

Continue operation. Continue to monitor. Take no action. Log

Only.

Unit Cycles < (less than) 3 Times per

Hour

Continue operation. Continue to monitor. Take no action. Log

Only.

Discharge Air > (greater than) 185 F Shutdown electric heater until temp is 100°F. Resume

operation.

Discharge Air Temperature Sensor

is Open or Shorted

Override Sensor. Set temp to 75°F. Continue to monitor. Set

error code 14 ON.

Temperature Beyond Operating

Limits

Ambient temp < (less than) 0°F and ambient temp > (greater

than) 130°F. Set error code 16 ON. When cleared return unit to

normal.

Outdoor Coil Temperature < 30 F

for 2 consecutive Minutes

Unit will use electric heat to satisfy heating demands until temp

is greater than 45°F. Unit must be a Heat Pump with electric

heat.

Frost Protection.

Unit will run active defrost for up to 6 minutes when Heat Pump

run time is greater than 60 minutes and outdoor coil temp is 26 F

or less.

TROUBLESHOOTING

Diagnostic Codes

Figure 710 (Fault Codes)

Содержание Kuhl KCQ06A10A















































































Результаты поиска

Содержание Kuhl KCQ06A10A

Отзывы:

Похожие инструкции для Kuhl KCQ06A10A

Бренды по названию

Популярные бренды

Friedrich Kuhl KCQ06A10A, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание Kuhl KCQ06A10A

Отзывы:

Похожие инструкции для Kuhl KCQ06A10A

Бренды по названию

Популярные бренды