Friedrich 920-087-09 (12/10) Скачать руководство пользователя страница 10

Страница: 10 / 36

FRP011

DRAIN TUBE

SIDE VIEW

FRONT VIEW

WALL SLEEVE

OPTIONAL AREA

PREFERRED AREA-

NO FOAM INSULATION

IF THE DRAIN MUST BE

LOCATED IN THE OPTIONAL

AREA, THE FOAM INSULATION

MUST BE CUT AWAY AND

REMOVED TO ALLOW ACCESS

TO THE DRAIN.

NUT

MOUNTING

PLATE

GASKET

SCREW

Figure 11

Drain Kit Location and Installation

PXDR10

QUANTITY

DESCRIPTION

COVER PLATES

MOUNTING PLATE

DRAIN TUBE

MOUNTING PLATE GASKET

#10 X ½” SHEET METAL SCREWS

#10-24 X ½ ” MACH. SCREWS

#10-24 X ½" LOCKNUTS

Remove.the.backing.from.the.gasket.and.mount.it.on.the.flat.side.

of.the.mounting.plate...(See.Figure.12,.Page.11)...Insert.the.drain.

tube.through.the.hole.in.the.gasket.and.mounting.plate.so.the.tube.

flange.will.be.against.the.wall.sleeve.

Position.the.assembly.beneath.the.drilled.holes.and.secure.it.with.

#10-24.x.½".machine.screws.and.lock.nuts.provided...Seal.the.tops.

of.the.screws.with.silicone.caulking..

Use.½".I.D..copper.tube,.PVC.pipe,.or.vinyl.hose.(obtained.locally).

to.connect.the.internal.drain.tube.to.the.drain.system.in.the.building.

Referring.to.Figure.12,.Detail.A,.Page.11,.locate.and.assemble.the.

(2).two.cover.plates.and.gaskets.over.the.drain.holes.at.the.rear.

of.the.wall.sleeve...Attach.them.with.the.#10.sheet.metal.screws.

provided...Make.certain.that.the.four.overflow.slots.at.the.rear.of.

the.wall.sleeve.are.not.blocked.(See.drawing.of.the.back.of.the.

sleeve.Figure.12,.Page.11).

If.a.deep.wall.extension.(PDXWSEXT).is.used,.after.installing.the.

field.supplied.flashing,.caulk.as.required...Be.sure.to.caulk.around.

the.flashing.and.the.wall.sleeve.where.the.hole.was.drilled.for.the.

drain.tube..

PXDR10 Drain Kit Installation

Instructions (optional for new

construction)

NOTE:

Determine.whether.drain.will.be.located.within.the.wall,.on.the.

indoor.side,.or.will.drain.to.the.exterior.of.the.building...Follow.

appropriate.instructions.below.depending.on.your.particular.

type.of.installation.

Internal Drain

NOTE:

If.installing.an.internal.drain,.you.MUST.install.a.drain.kit.on.

the.wall.sleeve.before.the.wall.sleeve.is.installed.

Refer.to.Figure.11.and.locate.the.drain.within.the.“Preferred”.

area.of.best.drainage...Maintain.at.least.a.½”.clearance.from.the.

embossed.area.

Using.the.mounting.plate.with.the.½”.hole.as.a.template,.mark.

and.drill.two,.3/16”.mounting.holes.and.a.½”.drain.hole.in.the.

sleeve.bottom.

Содержание 920-087-09 (12/10)





































Результаты поиска

Содержание 920-087-09 (12/10)

Отзывы:

Похожие инструкции для 920-087-09 (12/10)

Бренды по названию

Популярные бренды

Friedrich 920-087-09 (12/10), Инструкция по установке и эксплуатации

Результаты поиска

Содержание 920-087-09 (12/10)

Отзывы:

Похожие инструкции для 920-087-09 (12/10)

Бренды по названию

Популярные бренды