Frick Vyper 572 Скачать руководство пользователя страница 37

Страница: 37 / 76

VYPER

™

VARIABLE SPEED DRIVE

OPERATION

100-210 IOM (

JUL

09)

Page 37

QUANTUM

™

Lx PANEL SETUP

The Quantum

™

LX software provides the necessary controls

to operate Vyper

™

Drive and optional Harmonic Filter on Frick

screw compressors. This is accomplished through the recep-

tion of a Speed Command value (in rotations per minute),

Run Command signal from the Quantum

™

LX control panel

to the compressor motor.
The Quantum

™

LX control panel software will monitor motor

current values, system operating parameters, and fault flags

received from the Vyper

™

Drive to determine whether the

drive is operating safely. Any faults detected by the software

will result in an immediate shutdown of the compressor.

The specific fault information will then be displayed on the

control panel.
Additionally, the Quantum

™

LX control panel will control the

Vyper

™

Drive and compressor to the user-defined parameters

programmed at the control panel interface.

ACCESSING THE VYPER

™

SETUP

Specific options and setpoints must be configured at the

Quantum

™

LX control panel. These settings will provide the

Quantum

™

LX with the necessary information to safely control

the Vyper

™

Drive, and to shut the drive down in the event the

drive exceeds setpoint parameters.
The panel stores programmed setpoints into the panel

memory, however when first applying power to the panel,

all setpoints will be at default levels. The setpoints require

programming in order to operate the system properly.
The following paragraphs provide a step by step procedure to

properly set up the Quantum

™

LX control panel for operation.

Figure 35 shows the Operating Status Screen, which is dis-

played when power is applied to the Quantum

™

LX panel.

Figure 35 - Quantum

™

Lx Operating Status Screen

Содержание Vyper 572













































































Результаты поиска

Содержание Vyper 572

Отзывы:

Похожие инструкции для Vyper 572

Бренды по названию

Популярные бренды

Frick Vyper 572, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание Vyper 572

Отзывы:

Похожие инструкции для Vyper 572

Бренды по названию

Популярные бренды