Fresenius Medical Care GranuFlo 450385 Скачать руководство пользователя страница 23

Страница: 23 / 61

7 . 1 S P E C I F I C G R A V I T Y T E S T

P/N 450385 Rev H

Transfer Nozzle (top view)

Ball Valve Closed

7.1

RANSFER

OSE

LUSH AND

PECIFIC

RAVITY

EST

Once the Transfer Indicator Light flashes, the concentrate is ready to be tested. This test is done using

Hydrometer

, which measures the density of the acid concentrate. The resultant value is called the

“Specific Gravity.” The Specific Gravity is measured to verify that the concentrate has been properly

mixed.

ARNING

LWAYS CHECK THE

PECIFIC

RAVITY OF EACH NEW BATCH OF

CID

ONCENTRATE BEFORE USING

IN TREATMENT

UPPLYING AN IMPROPERLY MIXED

CID

ONCENTRATE TO THE

EMODIALYSIS

ACHINE

MAY RESULT IN PATIENT INJURY OR DEATH

To determine a Specific Gravity reading:

Prepare the hydrometer and the Hydrometer cylinder.

•

Check the hydrometer for cracks. Do not use a cracked Hydrometer.

•

Always handle the hydrometer with care. Always hold it vertically by the top, as finger marks

lower down can affect the accuracy of the instrument.

•

The hydrometer should never be held by the stem horizontally.

•

Rinse the hydrometer and the Hydrometer cylinder separately with purified water before

checking solution for Specific Gravity. The purified water source must meet

ANSI/AAMI

ISO

standards for dialysis currently

ANSI/AAMI RD62

, or

ISO 13959

•

Once the hydrometer

is clean, place it

onto a clean area.

Figure 9

Figure 10

Remove Transfer Hose from the top of the tank (Figure 9) and connect the Transfer Hose to

the Transfer Nozzle (Figure 10).

Hold the Transfer Nozzle and make

sure the Ball Valve on the Transfer

Nozzle is CLOSED (Figure 11).

Figure 11

Lower the locking levers of the Transfer Hose

Connector and lift up on the Transfer Hose to remove

from the side of the Unit.

Transfer Hose

With the Transfer Hose Connector locking levers

open, place the connector onto the end of the

Transfer Nozzle and pull back on the levers to lock the

Transfer Hose Connector in place.

Transfer

Nozzle

Transfer Hose

Содержание GranuFlo 450385






























































Результаты поиска

Содержание GranuFlo 450385

Отзывы:

Fresenius Medical Care GranuFlo 450385, Руководство оператора, Страница: 23 / 61

Результаты поиска

Содержание GranuFlo 450385

Отзывы: