Fresenius Medical Care 460018 Скачать руководство пользователя страница 21

Страница: 21 / 75

D I S S O L U T I O N C Y C L E C o n t i n u e d

P/N 460018 Rev. D

Remove the Dry Acid Dissolution Unit Small Access Lid and

slowly add granules as seen in Figure 7. This minimizes the

amount of particulates discharged into air while adding

granules to the tank. If clumping in dry acid product is present,

then the larger access lid can be used to load the Tank, but

ensure that the bags are slowly poured into the large access

port to avoid splashing of water onto the outside of the Dry

Acid Dissolution Unit (See Appendix A for further complete dry

acid mixing information, page 45).

Figure 7

10.

After the Dry Acid Concentrate has been added, remove the Large Access lid dry off the Final Fill Level

Sensor of any splashing that may have occurred during the add granules process (Figure 8).

Figure 8

11.

Replace the Large and Small Access Lid then press the

Dissolution side START button.

The Dry Acid Dissolution Unit will proceed to the MIX

Operation.



CAUTION!

E CERTAIN THE SAME

ATALOG

UMBER IS ON ALL CASES



CAUTION!

SING EYE PROTECTION AND GLOVES IS RECOMMENDED

F CONTACT WITH EYES

RINSE IMMEDIATELY

FOR

MINUTES

F CONTACT WITH SKIN

FLUSH WITH PLENTY OF SOAP AND WATER

ATERIAL

AFETY

ATA

HEET

(MSDS)

FOR FURTHER

ERSONAL

ROTECTIVE

QUIPMENT

(PPE)

OR EMERGENCY INSTRUCTIONS FOR THE

DRY ACID PRODUCT BEING USED

WARNING!

O NOT USE CASE OF DRY ACID CONCENTRATE THAT HAS BEEN OPENED OR TAMPERED WITH

T IS

IMPORTANT THAT THE ENTIRE CONTENTS OF EACH CASE OF DRY ACID CONCENTRATE IS EMPTIED INTO THE

CID

ISSOLUTION

NIT

E CERTAIN ALL BAGS PER CASE HAVE BEEN ADDED

WARNING

IN ABSENCE OF SIGNIFICANT CLUMPING

ONLY USE THE SMALL ACCESS LID WHEN POURING ACID

CONCENTRATE INTO THE MIXER

USE OF THE LARGE ACCESS LID WHEN POURING ACID CONCENTRATE MAY RESULT IN

INHALATION INJURY

NOTE:

RANU

CID

RODUCT CONTAINS

BAGS PER BOX AND

ITRASATE

DRY

WITH

CETATE

CID

RODUCT CONTAINS

BAGS PER BOX

ONTENTS OF ALL EIGHT BOXES MUST BE POURED INTO THE TANK

DURING THE

ADD

GRANULES

PERATION

NOTE:

NPUT WATER PRESSURE DIRECTLY EFFECTS HOW FAST

CID

ISSOLUTION

NIT WILL FILL

MAXIMUM INPUT WATER PRESSURE IS

PSI WITH A MINIMUM

GALLON PER MINUTE FLOW RATE

Locate Final Fill Sensor

Clean Final Fill Sensor with a soft cloth.

Содержание 460018












































































Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Medical Care 460018, Руководство оператора

Результаты поиска

Содержание 460018

Отзывы:

Бренды по названию

Популярные бренды