freightliner PE116DC Скачать руководство пользователя страница 43

Страница: 43 / 164

11. Place a pan under the coolant filter to catch en-

gine coolant.

12. Remove the coolant filter with a strap or chain

wrench. Install a new coolant filter and tighten.

13. Fill the cooling system with new coolant. The

cooling system is filled when the coolant level
reaches the MAX line on the surge tank. Refer to
the engine manufacturer’s service literature for
specific coolant information.

14. Replace the surge tank cap(s).

15. Return the hood to the operating position.

16. Start the engine and turn on the cab heater.

Allow the engine to warm up to normal operating
temperature. Check the radiator and hoses for
leaks. Repair as needed.

17. Shut off the engine, then check the coolant level

in the surge tank. Add coolant if the level isn’t at
the MAX line on the surge tank.

20–03 Fan Clutch Check (Noise

Emission Control)

Borg Warner (Kysor) K30 Fan
Clutch

Disconnect the batteries at the negative termi-
nals. Drain all air from the air system.

NOTE: the Borg Warner Service Alert Tool is
available at no cost. To get one, contact your
Borg Warner representative.

If the tool is not available, use a 0.062-inch
(1.57mm) feeler gauge to check the clutch wear.

Using the Borg Warner Service Alert Tool, check
the clutch wear as shown in

Fig. 4

, and

Fig. 5

If the tool is sitting below the retainer plate, the
fan clutch liner has remaining life.

If the tool is sitting above the retainer plate, re-
place the fan clutch liner.

Connect the battery cables.

Start the engine, and check for air leaks. Repair
as needed.

Horton DriveMaster® Fan Clutch

NOTE: If any part of the fan clutch needs to be
repaired or replaced after performing the checks
below, see

Group 20

of the vehicle Workshop

Manual.

Disconnect the batteries at the negative termi-
nals.

f200866

06/20/2016

With the fan clutch engaged, check the remaining life in
the clutch liner.

Fig. 4, Tool Below Retainer Plate, Liner Life Remaining

f200867

06/20/2016

With the fan clutch engaged, check the remaining life in
the clutch liner.

Fig. 5, Tool Above Retainer Plate, Liner Replacement

Needed

Engine Cooling/Radiator

New Cascadia Maintenance Manual, November 2019

20/3

Содержание PE116DC





































































































































































Результаты поиска

Содержание PE116DC

Отзывы:

Бренды по названию

Популярные бренды

freightliner PE116DC, Руководство по обслуживанию

Результаты поиска

Содержание PE116DC

Отзывы:

Бренды по названию

Популярные бренды