manualshive.com logo in svg

freightliner C SB FS65, Руководство по обслуживанию

Maintenance Manual для Freightliner C SB FS65 - это исчерпывающий руководство по обслуживанию и ремонту этого транспортного средства. Вы можете скачать этот manual бесплатно на нашем сайте. Загляните на manualshive.com, чтобы начать загрузку прямо сейчас.

Поделиться
Скачать
background image

26–01 Eaton/Fuller

Transmission Oil Level
Checking

1.

With the transmission at operating temperature,
and the vehicle on a level surface, check the oil
level in the transmission.

1.1

Clean the area around the fill plug, then
remove the plug from the side of the
case.

1.2

Using your finger or a bent pipe cleaner,
see if the oil is level with the fill opening.
See

Fig. 1

.

2.

If needed, fill the transmission with oil until level
with the lower edge of the fill opening. See

Table 1

for approved lubricants.

Approved Lubricants, Eaton/Fuller Transmissions

*

Lubricant Type

Temperature

SAE

Viscosity

Heavy-Duty Engine

Oil

API Service

Classification

SF or CD

Above +10°F (–12°C)

40 or 50

Below +10°F (–12°C)

30

*

Do not mix types of oil.

Table 1, Approved Lubricants, Eaton/Fuller

Transmissions

CAUTION

Operating an Eaton/Fuller transmission with the
oil level higher or lower than recommended can
result in transmission damage. Do not overfill the
transmission; overfilling will force oil out of the

case through the main shaft openings. Oil over-
flow may also drain onto the clutch or clutch
brake, causing additional problems.

IMPORTANT: Do not mix types of oil, because
of possible incompatibility. Do not use oil addi-
tives, friction modifiers, or synthetic lubricants.

3.

Clean the fill plug, then install it in the transmis-
sion. Tighten the plug as follows:

20 to 25 lbf·ft (27 to 34 N·m) for a 3/4-inch plug;

60 to 75 lbf·ft (81 to 102 N·m) for a 1-1/4 inch
plug.

26–02 Eaton/Fuller

Transmission Oil
Changing and Magnetic
Plug Cleaning

Draining

1.

Clean the area around the fill plug.

2.

Remove the fill plug from the side of the case.
Remove the drain plug(s) from the bottom of the
transmission case.

3.

Drain the oil while the transmission is warm.

4.

Clean the magnetic plug(s) before installing.
(Use a piece of key stock, or any other conve-
nient steel slug, to short the two magnetic poles
and divert the magnetic field.) Install and tighten
the drain plug(s) 20 lbf·ft (27 N·m).

Filling

1.

Add oil until it is level with the lower edge of the
fill opening. See

Fig. 1

. If the transmission has

two fill openings, add oil to the level of both fill
openings. See

Table 1

for approved transmission

lubricants, and

Table 2

for lubricant capacities.

CAUTION

Operating an Eaton/Fuller transmission with the
oil level higher or lower than recommended can
result in transmission damage. Do not overfill the
transmission; overfilling will force oil out of the
case through the main shaft openings. Oil over-

f260006b

10/05/94

A

B

A. Full
B. Low

Fig. 1, Manual Transmission Oil Level Checking

Transmission

26

School Bus Chassis Maintenance Manual, March 2003

26/1

Содержание C SB FS65




























































































Отзывы:

Нет отзывов

Похожие инструкции для C SB FS65

Astral Pool 57434 Manual preview
57434
Бренд: Astral Pool Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды