33–03 Tie Rod Lubrication,
Meritor Axles
For any Meritor axle that requires lubrication of the
tie-rod ends, wipe the grease fittings clean, then
pump multipurpose chassis grease, NLGI Grade 1
(6% 12-hydroxy lithium stearate grease) or NLGI
Grade 2 (8% 12-hydroxy lithium stearate grease),
into the tie-rod ends until all used grease is forced
out and fresh grease is seen at the ball stud neck.
33–04 All-Axle Alignment
Check
Drive-Axle Alignment Checking
Check the axle alignment, parallelism, and thrust
angle measurements for the rear drive axles. Use the
applicable procedure and specifications in
Group 35
of the
Century Class Trucks Workshop Manual
.
Toe-in Inspection
For vehicle alignment to be accurate, the shop floor
must be level in every direction. The turn plates for
the front wheels must rotate freely without friction,
and the alignment equipment must be calibrated
every three months by a qualified technician from the
equipment manufacturer. Freightliner dealers must
have proof of this calibration history.
1.
Apply the parking brakes, and chock the rear
tires.
2.
Raise the front of the vehicle until the tires clear
the ground. Check that the safety stands will
support the combined weight of the cab, axle,
and frame. Place safety stands under the axle.
3.
Using spray paint or a piece of chalk, mark the
entire center rib of each front tire.
4.
Place a scribe or pointed instrument against the
marked center rib of each tire, and turn the tires.
The scribe must be held firmly in place so that a
single straight line is scribed all the way around
each front tire.
5.
Place a turn-plate or turntable under both front
tires. Remove the safety stands from under the
axle, then lower the vehicle. Remove the lock-
pins from the gauges; make sure the tires are
exactly straight ahead.
NOTE: If turn-plates or turntables are not avail-
able, lower the vehicle. Remove the chocks
from the rear tires and release the parking
brakes. Move the vehicle backward and then
forward about six feet (two meters).
6.
Place a trammel bar at the rear of the front tires;
locate the trammel pointers at spindle height,
and adjust the pointers to line up with the scribe
lines on the center ribs of the front tires. See
. Lock in place. Check that the scale is set
on zero.
7.
Place the trammel bar at the front of the tires,
see
, and adjust the scale end so that the
pointers line up with the scribe lines. See
8.
Read the toe-in from the scale, and compare it to
the toe-in specification in
Group 33
of the
Century Class Trucks Workshop Manual
. If cor-
f330082a
10/05/2016
A
B
NOTE: B minus A equals toe-in.
Fig. 3, Wheel Toe-In (overhead view)
f330014a
10/05/2016
Fig. 4, Trammel Bar Positioning
Front Axle
33
Century Class Trucks Maintenance Manual, August 2017
33/2
Содержание Argosy COE 2011
