FreeWave LRS-455-EU Скачать руководство пользователя страница 28

Страница: 28 / 38

LRS-455-EU Data Transceiver Users Manual

LUM0032AA Rev A

Version 1.0

Radio Information

Radio Statistics in the Main Menu allows the user to view data transmission statistics gathered by the

transceiver during the most recent session. This is valuable when the user needs to know the signal

strength and noise levels of the link. Statistics are gathered during each data link and are reset when the

next link begins. See display below.

UMBER OF

ISCONNECTS

Any time the link between the Master and the Slave is broken and the radios lose Carrier Detect, it is

recorded in the Number of Disconnects value. The value indicates the total number of disconnects that

have occurred from the time the transceiver is powered on until the radio is put into Setup mode. Under

ideal operating conditions, the number of disconnects should be 0. One or more disconnects may indicate

a weak link, the presence of severe interference problems or loss of power to any of the radios in the link.

NTENNA

EFLECTED

OWER

This is a measurement of the transmitted power that is reflected back into the transceiver from

mismatched antennas or cables, or loose connections between the transceiver and antenna. A reading

of 0-5 is good; 5-30 is acceptable; 30+ indicates that the connections should be inspected for loose

connections and cable quality.

VERAGE

OISE

EVEL

The average noise level indicates the level of background noise and interference at this transceiver. The

number is an average of the noise levels measured at each frequency in the transceiver’s frequency hop

table. The individual measurement values at each frequency hop channel are shown in the frequency

table. Pressing the

Enter

key when the Radio Statistics menu is displayed, accesses the frequency table.

Содержание LRS-455-EU







































Результаты поиска

Содержание LRS-455-EU

Отзывы:

Похожие инструкции для LRS-455-EU

Бренды по названию

Популярные бренды

FreeWave LRS-455-EU, Руководство пользователя

Результаты поиска

Содержание LRS-455-EU

Отзывы:

Похожие инструкции для LRS-455-EU

Бренды по названию

Популярные бренды