Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 1153

background image

Signal Description

MPC5565 Microcontroller Reference Manual, Rev. 1.0

2-32

Freescale Semiconductor

2.3.8.18

External Trigger / GPIO
ETRIG[0:1]_GPIO[111:112]

External trigger signals trigger a software or hardware event. The eQADC can detect rising edge, falling
edge, high level, and low level on each of the external trigger signals. The eQADC also supports
configurable digital filters for these external trigger signals.

The eQADC external trigger input pins can be connected to the eTPU, the eMIOS, or an external signal.
The source is selected by configuring the eQADC trigger source in the SIU_ETISR register. Refer to

.

ETRIG[0] is the external trigger for CFIFO0, CFIFO2, and CFIFO4, and ETRIG[1] serves as the external
trigger for CFIFO1, CFIFO3, and CFIFO5.

GPIO[111:112] are general purpose input/output functions.

These signals are not supported in the 324 package.

2.3.8.19

Voltage Reference High
V

RH

V

RH

is the voltage reference high input pin for the eQADC.

2.3.8.20

Voltage Reference Low
V

RL

V

RL

is the voltage reference low input pin for the eQADC.

2.3.8.21

Reference Bypass Capacitor
REFBYPC

REFBYPC is a bypass capacitor input for the eQADC. The REFBYPC pin is used to connect an external
bias capacitor between the REFBYPC pin and V

RL

. The value of this capacitor must be 100nF. This bypass

capacitor is used to provide a stable reference voltage for the ADC.

2.3.9

Enhanced Time Processing Unit (eTPU) Signals

2.3.9.1

eTPU A TCR Clock / External Interrupt Request / GPIO
TCRCLKA_IRQ[7]_GPIO[113]

TCRCLKA_IRQ[7]_GPIO[113] is the TCR clock input for the eTPU A module. The alternate function is
an external interrupt request input for the SIU module.

«
...
87
88
89
90
91
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: iCeeO2 Страницы: 7

Бренд: Abov Страницы: 138

Бренд: Aurora Scientific Страницы: 21

Бренд: Clare Controls Страницы: 3

Бренд: Swegon Страницы: 11

Бренд: ICStation Страницы: 3

Бренд: C Systems Страницы: 4

Бренд: Zennio Страницы: 30

Бренд: Broan Страницы: 2

Бренд: Atmel Страницы: 150

Бренд: Zennio Страницы: 2

Бренд: TDSi Страницы: 23

Бренд: Licht-Technik Страницы: 13

Бренд: Inverter Страницы: 2

NetController B042-004

Бренд: Tripp Lite Страницы: 2

Бренд: H3C Страницы: 90

Бренд: Wolf Страницы: 2

Бренд: dunkermotoren Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды