Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 882 | Manualshive

Страница: 882 / 1153

background image

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

19-59

shows the modified transfer format for CPHA = 0. Only the condition where CPOL = 0 is

illustrated. The delayed master sample points are indicated with a lighter shaded arrow.

Figure 19-34. DSPI Modified Transfer Format (MTFE = 1, CPHA = 0, f

SCK

=

f

SYS

/ 4)

19.4.7.4

Modified SPI/DSI Transfer Format (MTFE = 1, CPHA = 1)

At the start of a transfer the DSPI asserts the PCS signal to the slave device. After the PCS to SCK delay
has elapsed the master and the slave put data on their SOUT pins at the first edge of SCK. The slave
samples the master SOUT signal on the even numbered edges of SCK. The master samples the slave
SOUT signal on the odd numbered SCK edges starting with the 3rd SCK edge. The slave samples the last
bit on the last edge of the SCK. The master samples the last slave SOUT bit one half SCK cycle after the
last edge of SCK. No clock edge is visible on the master SCK pin during the sampling of the last bit. The
SCK to PCS delay must be greater or equal to half of the SCK period.

NOTE

For the modified transfer format to operate correctly, you must thoroughly
analyze the SPI link timing budget.

t

CSC

= PCS to SCK delay.

t

ASC

= After SCK delay.

System clock

1

2

3

4

5

6

PCS

x

t

ASC

SCK

Master sample

Slave SOUT

Master SOUT

System clock

System clock

Slave sample

t

CSC

«
...
880
881
882
883
884
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Quantum Страницы: 20

Бренд: Linak Страницы: 2

Enclosure ENCR-10

Бренд: suprema Страницы: 18

Бренд: Computherm Страницы: 40

CYPRESS Traveo S6J335 Series

Бренд: Infineon Technologies Страницы: 308

Бренд: fadini Страницы: 40

Бренд: Airone Страницы: 2

Бренд: HobbyKing Страницы: 16

UltraVista 4K VWL-T122-4K-DP

Бренд: Rose electronics Страницы: 28

Бренд: MPPT Страницы: 8

Wi-Fi supla SLW-01

Бренд: Zamel Страницы: 2

Бренд: Senninger Страницы: 32

Бренд: X10 Страницы: 3

Бренд: jablotron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды