Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 868

Страница: 868 / 1153

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

19-45

19.4.4.6.3

DSPI D Connectivity

The DSPI D connects to the eTPUA, eMIOS and SIU as shown in

Figure 19-23

Figure 19-23. DSPI D Connectivity

Table 19-21

lists the DSPI D connections.

eTPUA output channel 9

Input 2 on IMUX for external IRQ[12]

eTPUA output channel 10

Input 2 on IMUX for external IRQ[13]

eTPUA output channel 11

Input 2 on IMUX for external IRQ[14]

Table 19-21. DSPI D Connectivity Table

Connected to:

DSPI D

IN[

]

DSPI D
OUT[

]

Connected to:

eTPUA output channel 21

Input 3 on IMUX for external IRQ[14]

eTPUA output channel 20

Input 3 on IMUX for external IRQ[15]

eTPUA output channel 19

no connect

eTPUA output channel 18

no connect

eTPUA output channel 17

Input 3 on IMUX for external IRQ[2]

eTPUA output channel 16

Input 3 on IMUX for external IRQ[3]

eMIOS output channel 11

Input 3 on IMUX for external IRQ[4]

eMIOS output channel 10

Input 3 on IMUX for external IRQ[5]

eMIOS output channel 13

Input 3 on IMUX for external IRQ[6]

eMIOS output channel 12

Input 3 on IMUX for external IRQ[7]

Table 19-20. DSPI C Connectivity Table (continued)

eTPU Channel

DSPI C

IN[

]

DSPI C
OUT[

]

Connected to:

SIU / IMUX

IN3 IRQ[14]

IN3 IRQ[2]

IN3 IRQ[11]

•

IN3 IRQ[15]

IN3 IRQ[12]
IN3 IRQ[13]

DSPI D

IN 6
IN 7

OUT 0

eMIOS

CH 11

CH 10
CH 13
CH 12

OUT 1

OUT 4

OUT 13

•

eMIOS

CH 15

CH 14

OUT 14

OUT 15

eTPUA

CH 21

CH 16

•

CH 29

CH 24

•

IN 8
IN 9

•

IN 0

IN 5

IN 10

IN 15

•

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды