Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 631

Страница: 631 / 1153

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-54

Freescale Semiconductor

Figure 16-37

shows the unified channel in OPWMC with trailing dead-time.

Figure 16-37. Output PWMC with Trailing Dead-time Insertion

16.4.4.4.14

Output Pulse-Width Modulation Mode (OPWM)

The following table lists the output width modulation mode settings:

Table 16-27. OPWM Operating Modes

MODE[0:6]

Unified Channel OPWM Operating Mode

0b0100000

Output pulse-width modulation. FLAG set at match of internal counter and
comparator B, immediate update.

0b0100001

Output pulse-width modulation. FLAG set at match of internal counter and
comparator B, next period update.

0b0100010

Output pulse-width modulation. FLAG set at match of internal counter and
comparator A or comparator B, immediate update.

0b0100011

Output pulse-width modulation. FLAG set at match of internal counter and
comparator A or comparator B, next period update.

Output

flip-flop

A1 match A1 match

Time

0x000000

0x000303

0x000200

Update to

Selected

MODE[6] = 0

counter bus

A1 match

Notes:

Writing EMIOS_A

writes to A2.

Writing EMIOS_B

writes to B1.

A2 value transferred to A1 according to OU

bit.

B2 value transferred to B1 according to OU

bit.

Update to

A1 match

A1 value

0x000200

Update to

B1 match

0x000010

0x000000

B1 value

0x000010

Time

B1 match

0x000303

0xxxxxxx

EMIOS_CCNTR

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды