Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 450 | Manualshive

Страница: 450 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

12-5

•

Bus monitor

— User selectable

— Programmable timeout period (with 8 external bus clock resolution)

•

Port size configuration per chip select (16 or 32 bits)

•

Port size for calibration chip select is 16 bits

•

Configurable wait states (via chip selects)

•

Four chip select (CS[0:3]) signals

•

Support for dynamic calibration with up to three calibration chip selects
(CAL_CS[0] and CAL_CS[2:3]),

•

Write/byte enable (WE/BE) signals depend on the package: 324 BGA: two signals (WE/BE[0:1])

•

Configurable bus speed modes (1/2 or 1/4 of system clock frequency)

•

Module disable modes for power savings

•

Optional automatic CLKOUT gating to save power and reduce EMI

•

Compatible with MPC5xx external bus
Refer to

Section 12.4.1.18, “Compatible with MPC5xx External Bus (with Some Limitations)

.”

12.1.4

Modes of Operation

The mode of the EBI is determined by the MDIS and EXTM bits in the EBI_MCR. Refer to

Section 12.3.1.3, “EBI Module Configuration Register (EBI_MCR)

” for details. Configurable bus speed

modes and debug mode are modes that the MCU can enter, in parallel to the EBI being configured in one
of its module-specific modes.

12.1.4.1

Single Master Mode

In single master mode, the EBI responds to internal requests matching one of its regions, but ignores all
externally-initiated bus requests. The MCU is the only master allowed to initiate transactions on the
external bus in this mode; therefore, it acts as a parked master and does not have to arbitrate for the bus
before starting each cycle. Single master mode is entered when EXTM = 0 and MDIS = 0 in the
EBI_MCR.

NOTE

The MPC5565 does not include arbitration signals BR, BG, and BB.

12.1.4.2

External Master Mode

When the MCU is in external master mode, the EBI responds to internal requests matching one of its
regions, and also to external master accesses to internal address space. External master mode is entered
when EXTM = 1 and MDIS = 0 in the EBI_MCR register.

Because the MPC5565 does not have arbitration, the dual-master operation (multiple masters initiating
external bus cycles) is not supported. A multi-MCU system with one master and one slave is supported.

«
...
448
449
450
451
452
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: SYCLOPE electronic Страницы: 40

Бренд: BQT Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Kelly Страницы: 37

Бренд: Danfoss Страницы: 4

Бренд: VADDIO Страницы: 16

Бренд: tecatlantis Страницы: 68

Бренд: METRON Страницы: 34

Бренд: Botex Страницы: 36

Бренд: Hamamatsu Страницы: 50

Бренд: Aaeon Страницы: 54

Бренд: Elan Страницы: 2

Бренд: Oki Страницы: 466

Бренд: Aurora Страницы: 2

Бренд: YASKAWA Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды