Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 459 | Manualshive

Страница: 459 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-14

Freescale Semiconductor

12.3.1

Register Descriptions

12.3.1.1

Writing EBI Registers While a Transaction is in Progress

Other than the exceptions below, EBI registers must

not

be written while a transaction to the EBI (from

internal or external master) is in progress (or within 2 CLKOUT cycles after a transaction has just
completed, to allow internal state machines to go IDLE). In such cases, the behavior is undefined.

Exceptions that can be written while an EBI transaction is in progress are the following:

•

All bits in EBI_TESR

•

SIZE, SIZEN fields in EBI_MCR

Refer to

Section 12.5.1, “Booting from External Memory

,” for additional information.

12.3.1.2

Separate Input Clock for Registers

The EBI registers are accessed with a clock signal separate from the clock used by the rest of the EBI. In
module disable mode, the clock used by the non-register portion of the EBI is disabled to reduce power
consumption. The clock signal dedicated to the registers, however, allows access to the registers even
while the EBI is in the module disable mode. Flag bits in the EBI transfer error status register (EBI_TESR),
however, are set and cleared with the clock used by the non-register portion of the EBI. Consequently, in
module disable mode, the EBI_TESR does not have a clock signal and is therefore not writable.

12.3.1.3

EBI Module Configuration Register (EBI_MCR)

The EBI_MCR contains bits that configure various attributes associated with EBI operation.

Base (0xC3F8_4000)

Access: R/W

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

0

0

0

0

0

SIZEN

SIZE

0

0

0

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

ACGE

EXTM EARB

0

0

0

0

0

0

MDIS

0

0

0

0

0

DBM

W

Reset

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

Figure 12-2. EBI Module Configuration Register (EBI_MCR)

«
...
457
458
459
460
461
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: Hable Страницы: 3

Бренд: Danfoss Страницы: 36

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Samson Страницы: 2

Бренд: Lawler Страницы: 5

Бренд: RadioMaster Страницы: 10

Бренд: National Instruments Страницы: 34

Бренд: SOMFY Страницы: 56

Бренд: Texas Instruments Страницы: 27

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

Бренд: WINDY NATION Страницы: 16

Бренд: Sentiotec Страницы: 45

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: Winbond Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды