manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Frequency Modulated Phase Locked Loop and System Clocks (FMPLL)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

11-33

 

11.5

Document Revision History

Table 11-11. Changes Between MPC5565RM Revisions 0.1 and 1

In the Features list, changed:
 • From: “range from 48MHz to 132MHz “
 • To: “range from 48MHz to maximum device frequency”

In Section 11.4.2.6.1, “Alternate/Backup Clock Selection,” made this change:
 • From: “Note that when the FMPLL is operated in SCM the system frequency is dependent upon the value in RFD[0:2].”
 • To: “Note that when the FMPLL is operated in SCM, writes to FMPLL_SYNCR[RFD] have no effect on clock frequency

Added note to the Section 11.4.3.1, “Programming System Clock Frequency Without Frequency Modulation” section:

“When using crystal reference mode or external reference mode, The PREDIV value must not be set to any value that 

causes the phase/frequency detector to go below 4MHz. That is, the crystal or external clock frequency divided by the 
PREDIV value must be greater than or equal to 4MHz.”

Changed value of ENGCLK divider factors
 • From: 2 to 128
 • To:  2 to 126

Modified the LOCK bit to read:
PLL lock status bit. Indicates whether the FMPLL has acquired lock. If the LOCK bit is read when the FMPLL simultaneously 
loses lock or acquires lock, the bit does not reflect the current condition of the FMPLL.

If operating in bypass mode, LOCK remains cleared after reset. Refer to the for frequency as defined in the 

Data Sheet 

for 

the lock/unlock range.

0 PLL is unlocked.
1 PLL is locked.

Made changes in LOCKS bit:
 • From “a write to the FMPLL_SYNCR which modifies the MFD bits”
 • To: a write to the FMPLL_SYNCR which modifies the MFD and PREDIV bits”

In Section 11.4.2.2, “Reduced Frequency Divider (RFD)”:
 • From: “The RFD must be programmed to be 

≥

1 when changing MFD or PREDIV or when enabling frequency modulation” 

 • To: “To protect the system from frequency overshoot during the PLL lock detect phase, the RFD must be programmed to 

be 

≥

1 when changing MFD or PREDIV or when enabling frequency modulation.”

Added the symbols F

ref_crystal 

and F

ref_ext 

to the diagrams, and throughout the manual added further explanation of the fact 

that F

prediv

 is the frequency after the predivider. 

Modified Table 11-7 “Input Clock Frequency” by adding a column of frequency symbols. 

Modified Table 11-9 “Clock Out vs Clock In Relationships” by changing F

ref

 symbols to F

ref_crystal 

and F

ref_ext 

. 

Changed the range 16 -40 MHz to simply 40 MHz. 

Modified the crystal oscillator network figure to show resistor on the XTAL signal.

Section Table 11-5., “FMPLL_SYNSR Field Descriptions: for the LOCK bit description, added: If operating in bypass mode, 
LOCK remains cleared after reset. Refer to the frequency as defined in the 

MPC5565 Microcontroller Data Sheet

 for the 

lock/unlock range. 

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Parker A4W Series Installation And Service Information preview
A4W Series
Бренд: Parker Страницы: 12
Parkside PDWE 8 A1 Instructions Manual preview
PDWE 8 A1
Бренд: Parkside Страницы: 86
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Бренд: YASKAWA Страницы: 49
M-system MSP10 Instruction Manual preview
MSP10
Бренд: M-system Страницы: 17
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Бренд: IBC Страницы: 8
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Бренд: H.E. Anderson Страницы: 11
Kelly KLS2418ND User Manual preview
KLS2418ND
Бренд: Kelly Страницы: 37
Danfoss AMV 20 SL Operating Manual preview
AMV 20 SL
Бренд: Danfoss Страницы: 4
Z-Wave Alliance SR-ZV9002T4-CCT-RU Manual preview
SR-ZV9002T4-CCT-RU
Бренд: Z-Wave Alliance Страницы: 10
Omega Engineering PHCN-410 Operator'S Manual preview
PHCN-410
Бренд: Omega Engineering Страницы: 11
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Бренд: SUPMEA Страницы: 32
M-system EAR70 Instruction Manual preview
EAR70
Бренд: M-system Страницы: 8
S&S Northern Merlin 500S User Manual preview
Merlin 500S
Бренд: S&S Northern Страницы: 8
SHOWTEC 70237 Manual preview
70237
Бренд: SHOWTEC Страницы: 20
LOVATO ELECTRIC ATL800 Installation Manual preview
ATL800
Бренд: LOVATO ELECTRIC Страницы: 6
WifiTrax Model Science WFG-80 Getting Started Manual preview
WFG-80
Бренд: WifiTrax Model Science Страницы: 4
Oase ProfiLux Garden LED Controller Operating Instructions Manual preview
ProfiLux Garden LED Controller
Бренд: Oase Страницы: 116
Promise Technology SUPERTRAK TX8650 Quick Start Manual preview
SUPERTRAK TX8650
Бренд: Promise Technology Страницы: 191

Бренды по названию

Популярные бренды

Загрузить еще бренды