manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Direct Memory Access (eDMA)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

9-45

The TCD status bits execute the following sequence for a hardware activated channel:

1. eDMA peripheral request asserts (issued service request via hardware)

2. TCD.START = 0, TCD.ACTIVE = 1, TCD.DONE = 0 (executing)

3. TCD.START = 0, TCD.ACTIVE = 0, TCD.DONE = 0 (completed minor loop and is idle) or

4. TCD.START = 0, TCD.ACTIVE = 0, TCD.DONE = 1 (completed major loop and is idle)

For both activation types, the major loop complete status is explicitly indicated via the TCD.DONE bit. 

The TCD.START bit is cleared automatically when the channel begins execution regardless of how the 
channel was activated.

9.4.6.2

Active Channel TCD Reads

The eDMA reads the true TCD.SADDR, TCD.DADDR, and TCD.NBYTES values if read while a 
channel is executing. The true values of the SADDR, DADDR, and NBYTES are the values the eDMA 
engine is currently using in its internal register file and not the values in the TCD local memory for that 
channel. The addresses (SADDR and DADDR) and NBYTES (decrements to zero as the transfer 
progresses) can give an indication of the progress of the transfer. All other values are read back from the 
TCD local memory. 

9.4.6.3

Preemption Status

Preemption is only available when fixed arbitration is selected for both group and channel arbitration 
modes. A preempt-able situation is one in which a preempt-enabled channel is running and a higher 
priority request becomes active. When the eDMA engine is not operating in fixed group, fixed channel 
arbitration mode, the determination of the relative priority of the actively running and the outstanding 
requests become undefined. Channel and/or group priorities are treated as equal (or more exactly, 
constantly rotating) when round-robin arbitration mode is selected.

The TCD.ACTIVE bit for the preempted channel remains asserted throughout the preemption. The 
preempted channel is temporarily suspended while the preempting channel executes one iteration of the 
major loop. Two TCD.ACTIVE bits set at the same time in the overall TCD map indicates a higher priority 
channel is actively preempting a lower priority channel.

9.4.7

Channel Linking

Channel linking (or chaining) is a mechanism where one channel sets the TCD.START bit of another 
channel (or itself) thus initiating a service request for that channel. This operation is automatically 
performed by the eDMA engine at the conclusion of the major or minor loop when properly enabled. 

The minor loop channel linking occurs at the completion of the minor loop (or one iteration of the major 
loop). The TCD.CITER.E_LINK field are used to determine whether a minor loop link is requested. When 
enabled, the channel link is made after each iteration of the minor loop except for the last. 

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Бренд: Yamaha Страницы: 92
Kampmann 197901960988 Manual preview
197901960988
Бренд: Kampmann Страницы: 5
YASKAWA J1000 CIMR-JC series Option Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 26
Samson 46-7 Mounting And Operating Instructions preview
46-7
Бренд: Samson Страницы: 44
Hansen FROST MASTER Installation Manual preview
FROST MASTER
Бренд: Hansen Страницы: 12
Freescale Semiconductor RS08 Designer Reference Manual preview
RS08
Бренд: Freescale Semiconductor Страницы: 34
Matelec FPC-12720 Quick Start Manual preview
FPC-12720
Бренд: Matelec Страницы: 2
Linear Technology LTC3553EPD Quick Start Manual preview
LTC3553EPD
Бренд: Linear Technology Страницы: 5
ICP DAS USA WISE-5801 Application Example preview
WISE-5801
Бренд: ICP DAS USA Страницы: 20
iNels JA3-018M Quick Start Manual preview
JA3-018M
Бренд: iNels Страницы: 2
Watlow Ramping and Profiling Microprocessor-Based Control SERIES 1500 User Manual preview
Ramping and Profiling Microprocessor-Based Control SERIES 1500
Бренд: Watlow Страницы: 90
YOKOGAWA Revolution FA-M3 R Technical Information preview
Revolution FA-M3 R
Бренд: YOKOGAWA Страницы: 57
National Instruments AMUX-64T Installation Manual preview
AMUX-64T
Бренд: National Instruments Страницы: 3
Kelly KLS14801-8080N User Manual preview
KLS14801-8080N
Бренд: Kelly Страницы: 43

Бренды по названию

Популярные бренды

Загрузить еще бренды