manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor MC9S12ZVM series Скачать руководство пользователя страница 130

Chapter 4 Interrupt (S12ZINTV0)

MC9S12ZVM Family Reference Manual  Rev. 1.3

130

Freescale Semiconductor

•

One non-maskable unimplemented page2 op-code trap

•

One non-maskable software interrupt (SWI)

•

One non-maskable system call interrupt (SYS)

•

One non-maskable machine exception vector request

•

One spurious interrupt vector request

•

One system reset vector request

Each of the I-bit maskable interrupt requests can be assigned to one of seven priority levels supporting a
flexible priority scheme. The priority scheme can be used to implement nested interrupt capability where
interrupts from a lower level are automatically blocked if a higher level interrupt is being processed.

4.1.1

Glossary

The following terms and abbreviations are used in the document.

4.1.2

Features

•

Interrupt vector base register (IVBR)

•

One system reset vector (at address 0xFFFFFC).

•

One non-maskable unimplemented page1 op-code trap (SPARE) vector (at address vector base

1

+

0x0001F8).

•

One non-maskable unimplemented page2 op-code trap (TRAP) vector (at address vector base

1

 +

0x0001F4).

•

One non-maskable software interrupt request (SWI) vector (at address vector base

1

 + 0x0001F0).

•

One non-maskable system call interrupt request (SYS) vector (at address vector base

1

 +

0x00001EC).

•

One non-maskable machine exception vector request (at address vector base

1

 + 0x0001E8

)

.

•

One spurious interrupt vector (at address vector base

1

 + 0x0001DC).

•

One X-bit maskable interrupt vector request associated with XIRQ (at address vector base

1

 +

0x0001D8).

Table 4-2. Terminology

Term

Meaning

CCW

Condition Code Register (in the S12Z CPU)

DMA

Direct Memory Access

INT

Interrupt

IPL

Interrupt Processing Level

ISR

Interrupt Service Routine

MCU

Micro-Controller Unit

IRQ

refers to the interrupt request associated with the IRQ pin

XIRQ

refers to the interrupt request associated with the XIRQ pin

1. The vector base is a 24-bit address which is accumulated from the contents of the interrupt vector base register (IVBR, used
as the upper 15 bits of the address) and 0x000 (used as the lower 9 bits of the address).

Содержание MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды