Freescale Semiconductor e200z3 Скачать руководство пользователя страница 277 | Manualshive

Страница: 277 / 442

background image

External Core Complex Interfaces

e200z3 Power Architecture Core Reference Manual, Rev. 2

Freescale Semiconductor

7-9

describes transfer attribute signals, which provide additional information about the bus transfer

cycle. Attributes are driven with the address at the start of a transfer.

Table 7-4. Descriptions of Signals for the Address and Data Buses

Signal

I/O

Signal Description

p_[d,i]_haddr[31:0]

O

Address bus. Provides the address for a bus transfer. According to the AHB definition,
p_[d,i]_haddr[31] is the msb and p_[d,i]_haddr[0] is the lsb.

p_[d,i]_hrdata[63:0
]

I

Read data bus. Provides data to the core on read transfers. The read data bus can transfer 8, 16, 24,
32, or 64 bits per transfer. According to the AHB definition,

p_[d,i]_hrdata63 is the msb and

p_[d,i]_hrdata0 is the lsb.

Memory Byte AddressWired to

p_[d,i]_hrdata Bits

0007:0
00115:8
01023:16
01131:24
10039:32
10147:40
11055:48
11163:56

p_d_hwdata[63:0]

O

Write data bus. Transfers data from the core on write transfers. The write data bus can transfer 8, 16,
24, 32, or 64 bits of data per bus transfer. According to the AHB definition,

p_d_hwdata[63] is the msb

and

p_d_hwdata[0] is the lsb.

Memory Byte AddressWired to

p_d_hwdata Bits

0007:0
00115:8
01023:16
01131:24
10039:32
10147:40
11055:48
11163:56

Table 7-5. Descriptions of Transfer Attribute Signals

Signal

I/O

Signal Description

p_[d,i]_htrans[1:0]

O

Transfer type. The processor drives

p_[d,i]_htrans[1:0] to indicate the current transfer type as follows:

00 IDLE—No data transfer is required. Slaves must terminate IDLE transfers with a zero wait-state

OKAY response and ignore the (non-existent) transfer.

01 BUSY—(The core does not use the BUSY encoding and does not present this type of transfer to

a bus slave.) Master is busy; burst transfer continues.

10 NONSEQ—Indicates the first transfer of a burst, or a single transfer. Address and control signals

are unrelated to the previous transfer.

11 SEQ—Indicates the continuation of a burst. Address and control signals are related to the previous

transfer. Control signals are the same. Address was incremented by the size of the data transferred
(optionally wrapped).

If the

p_[d,i]_htrans[1:0] encoding is not IDLE or BUSY, a transfer is being requested.

p_[d,i]_hwrite

O

Write. Defines the data transfer direction for the current bus cycle.

State

Meaning

Asserted—The current bus cycle is a write.
Negated—The current bus cycle is a read.

«
...
275
276
277
278
279
...
»

Содержание e200z3



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e200z3

Бренд: Campbell Страницы: 42

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

ELC-LTTR240-TBP

Бренд: ENERMAX Страницы: 16

Бренд: Cypress Semiconductor Страницы: 33

Бренд: Xenteq Страницы: 16

Бренд: Maxtor Страницы: 2

Бренд: Xilinx Страницы: 27

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Promise Technology Страницы: 148

Бренд: Quatech Страницы: 5

Бренд: Wavtech Страницы: 8

Бренд: IEI Technology Страницы: 106

Бренд: IceManCooler Страницы: 2

Бренд: ADTRAN Страницы: 4

mvHYPERION-32R16

Бренд: Matrix Vision Страницы: 148

Бренд: Intel Страницы: 57

Бренд: WEIGL Страницы: 6

Бренд: VALKYRIE Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды