manualshive.com logo in svg

FRC TACHPLUS+ TPA400, Руководство пользователя, Страница: 12 / 24

Поделиться
Скачать
FRC TACHPLUS+ TPA400 Скачать руководство пользователя страница 12

TPA400 Rev0509

12

OPERATION

The TACHPLUS+ displays crucial engine information to the pump operator. The

audible alarm is a clear distinctive warning that sounds when a monitored  input exceeds
normal parameters. Visual warnings for the two LED displays will flash to indicate
warnings visually to the pump operator.

The Message Display will show all warning messages or other requested

information.

Message Mode Operation

There are two buttons on the TachPlus: a 

MODE

 and a 

SILENCE

 button. In

message mode, system messages are shown in the message display.  To enter message
mode, press the 

MODE

 button. Every push of the 

MODE

 button displays the next

message. Each message remains in the window until the 

MODE

 button is pressed

again. If there is any warning, the message will be shown in the message display in 10
second intervals. This message will flash to indicate that it is a warning. Press the

SILENCE

 button to return to the normal display. Once exiting the message mode,

pressing the 

MODE

 button again will show the last displayed message.

To scroll through the messages, press and hold the 

MODE

 button and press the

SILENCE

 button. In scroll mode, the display will continuously scroll through all

messages available. If there is any warning, it will be added to the bank of scrolling
messages every 10 seconds. The warning message will flash to alert the operator.
Pressing the 

SILENCE

 button will bring the display back to the normal mode.

Visual Alarm

Whenever there is a monitored failure or problem, the visual alarm will be activated.

This alarm cannot be reset or cancelled manually. The alarm will stop automatically
when the problem has been taken care of.

Audiable Alarm

The Tachplus has a very unique sound feature. The Audible Status Warning System

gives a short clear distinctive signal as the pump is engaged. It sounds continuously if
there is a monitored failure such as low oil pressure or high engine temperature. It
sounds a dual burst for low fuel warning.

Silencing Audible Alarm

All audible alarms can be cancelled by pressing the  

SILENCE

 button. Pressing

the 

SILENCE

 button for 2 seconds turns the buzzer or audible warning off. Pressing

it for 2 seconds again will reactivate the audible warning. Pressing the 

SILENCE

button will not change  the visual warning.

Содержание TACHPLUS+ TPA400

























Отзывы:

Нет отзывов