manualshive.com logo in svg

FRC AUTOFOAM FSA015, Руководство пользователя

Поделиться
Скачать
FRC AUTOFOAM FSA015 Скачать руководство пользователя страница 8

FSA100 Rev1206

8

Controls and Indicators

All controls and indicators are located on the front of the control module. It contains

the push button electronic controls and digital displays. (Refer to Figure 2.)

OFF Button

Press this button to turn the AutoFoam system off. The metering valve will go to

the closed position.

FOAM ON Button

Press this button to put the AutoFoam system in the automatic mode. It is used at

start up, to exit the manual override mode, or to show the selected foam percent in the
upper display.

Upper Display

 An upper multifunction display shows foam concentrate flow, selected foam

percent, or the total gallons of foam concentrate used. The display will show OFF
when the system is off. When the system is turned on the selected foam percent is
displayed for three seconds then foam flow is displayed. When the FOAM % buttons
are pressed the display will show the selected foam percent for three seconds then go
back to show foam flow.

FOAM % Buttons

Press these buttons to raise or lower the percent of foam that is inducted. When

the increase or decrease button is pressed the upper display will show the selected
percent.

Lower Display

 A lower multifunction display shows the discharge flow rate and the total gallons

of water used. If there is water flow on the discharge side of the pump, flow rate will
be displayed even if the AutoFoam system is off.

TOTAL Button

Press and hold the TOTAL button to display the total gallons of foam (upper

display x 1) and water (lower display x 100) that has been discharged.

Manual OVERRIDE Buttons

Press and hold the OPEN or CLOSE button for three seconds to set the system in

manual mode. The upper and lower displays will flash to indicate the system is in
manual mode and they will continue to show correct foam and water flow rates. In the
manual mode the operator is in control of opening or closing the foam metering valve
to set how much foam concentrate flows. To exit the manual mode the FOAM ON
button is pressed to start the automatic mode or the OFF button is pressed to turn the
system off.

Содержание AUTOFOAM FSA015


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды