manualshive.com logo in svg

Franklin Electric SubDrive1100 Connect IP 23, Руководство пользователя

Поделиться
Скачать
Franklin Electric SubDrive1100 Connect IP 23 Скачать руководство пользователя страница 4

4

SubDrive Connect

Declaration of Conformity

MOTOR OVERLOAD PROTECTION NOTE:

The drive electronics provide motor overload protection by preventing motor current from exceeding the 
maximum Service Factor Amps (SFA). Motor overtemperature sensing is not provided by the drive.

BRANCH CIRCUIT PROTECTION

Integral solid state short circuit protection does not provide branch circuit protection. Branch circuit 
protection must be provided in accordance with the National Electrical Code and any additional local 
codes, or the equivalent. Drive shall be protected by inverse-time fuse or Circuit breaker only, rated 300 
V, maximum and per the full-load motor output current rating as noted in the Fuse/Circuit Breaker and 
Wire Sizing section on pg. 20.

INTERNAL LITHIUM BATTERY

CAUTION: Never place lithium batteries in mouth. If swallowed, contact your physician or local poison 
control center. If battery is damaged, do not use. Battery shall be serviced or replaced by a quali ed 
serviceman.

Store new batteries only in the manufacturer's containers. Dispose/recycle used and damaged batteries 
per local, regional, and national laws and regulations.

MAINTENANCE

Unless needed by accessory kit or noted within this manual, no additional SubDrive maintenance is 
required.

Wi-Fi MODULE

The Wi-Fi module has been tested and found to comply with part 15 of FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference. This equipment generates, 
uses, and can radiate radio frequency energy for limited periods (approx. 15 min.) and, if the drive 
is not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment o  and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit di erent from that to which the receiver is
connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Model No.

Model Description

5870205153C

SubDrive 1100 Connect IP23

5870205353C

SubDrive 1500 Connect IP23

5870205453C

SubDrive 2200 Connect IP23

E184902

Содержание SubDrive1100 Connect IP 23





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды