manualshive.com logo in svg

Franklin Electric SubDrive Connect Plus SDCP-SUB1023, Быстрый старт

Поделиться
Скачать
Franklin Electric SubDrive Connect Plus SDCP-SUB1023 Скачать руководство пользователя страница 10

QUICKSTART GUIDE

SubDrive Connect Plus Mobile App

10

SubDrive Connect Plus Mobile App

The SubDrive Connect Plus Mobile App provides live monitoring of system performance, advanced trouble

-

shooting, fault log monitoring, and advanced configuration of the SubDrive Connect Plus.

Setup Bluetooth Connection

After installing the app on your mobile device, use the following procedure to connect to the drive:
1.

From the Home screen, tap “Connect New Product.”

2. On the 

New Product Wizard

 screen, tap either 

Scan QR Code Sticker

 or 

Enter the Bluetooth Key

.

3. If using the scanning tool, center the QR code on the drive in the screen. If the code is missing or 

unreadable, the code can be displayed on the screen. Refer to 

“Menu Navigation” on page 8

.

4. If using the Bluetooth key, also available onscreen.
5. Enter a Name and Location to identify the drive within the app.
6. Tap Finish & Connect to complete the connection.

Using the SubDrive Connect Plus Mobile App 

To communicate with a SubDrive Connect Plus that has been paired with the app:
1.

On the 

My Products

 screen, tap the name of the drive to connect to the device and enter the Dashboard.

2. Tap the 

MENU

 button to for a list of options.

3. Tap 

Setup

 to change VFD settings

Содержание SubDrive Connect Plus SDCP-SUB1023













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды