manualshive.com logo in svg

Franklin Electric MonoDrive, Руководство по установке, Страница: 5 / 48

Поделиться
Скачать
Franklin Electric MonoDrive Скачать руководство пользователя страница 5

SubDrive/MonoDrive

5

Description and Features

The Franklin Electric SubDrive/MonoDrive is a dependable residential water system controller 
that uses advanced electronics to enhance the performance of standard submersible pumps. 

When used with the specified Franklin Electric motor (see Table 1, pg. 4), the SubDrive/

MonoDrive eliminates pressure cycling associated with conventional water well systems and 
owners of private water well systems can enjoy “city-like” water pressure.

In addition, the reduced tank size (see Table 4, pg. 29) allows installation in small spaces. 

SubDrive/MonoDrive Key Features:

  •  Constant water pressure with a wide range of settings (25-80 psi) (1.7-5.4 bar)
  •  Smaller pressure tank can be used
  •  Fits the pump to the application – pump speed is controlled to provide  

 

 

 

  the optimum performance without overloading the motor

  •  Flexibility – this unit can be used with standard off-the-shelf pumps
  •  No in-rush (power-on transient) current
  •  Low motor start-up current (soft-starting)
  •  Active Power Factor Correction minimizes input RMS current

Protection Features: 

  •  Dry well conditions – with smart pump monitoring (see Figure 1, pg. 20)
  •  Bound pump – with auto-reversing torque
  •  High voltage / lightning surge
  •  Low line voltage
  •  Open motor circuit
  •  Short circuit

Status
État
Estado 

Содержание MonoDrive

















































Отзывы:

Нет отзывов