Franklin Electric Cerus X-Drive Скачать руководство пользователя страница 110

Страница: 110 / 156

MAINTENANCE

Fan Replacement

110

Frame D Heat Sink Fan

Remove four screws to release and slide out the fan assembly. When replacing screws, tighten to a
torque of 20.8 to 22.1 in. lbs. (2.35 to 2.5 Nm).

2. Disconnect the power connectors before completely removing the fan.

Frame D Capacitor Fan

Remove two screws and press the tabs on both sides to remove the lower cover. When replacing
screws, tighten to a torque of 10.4 to 13 in. lbs. (1.18 to 1.47 Nm).

2. Press the top of the keypad and remove the keypad.
3. Remove two screws and press the tabs on both sides to remove the upper cover. When replacing

screws, tighten to a torque of 5.2 to 6.9 in. lbs. (0.59 to 0.78 Nm).

4. Disconnect fan power connector.
5. Remove one screw and pull out the fan. When replacing the screw, tighten to a torque of 8.9 to 10.4 in.

lbs. (1.0 to 1.18 Nm).

Содержание Cerus X-Drive





























































































































































Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды

Franklin Electric Cerus X-Drive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cerus X-Drive

Отзывы:

Похожие инструкции для Cerus X-Drive

Бренды по названию

Популярные бренды