Fractal Axe-Fx Скачать руководство пользователя

Страница: 207 / 211

SPECIFICATIONS

Doc Q7.0

195

Specifications

Axe-Fx II XL/XL+ Specifications

17.1

FRONT PANEL INPUT

Connector:

1/4” phone jack, unbalanced.

Impedance:

1 MegaOhm (less if Input Impedance is active)

Max. Input Level:

+16 dBu (conditioned for guitar use)

REAR INPUTS

Connector:

1/4” phone jack, balanced.

Impedance:

1 MegaOhm

Max. Input Level:

+20 dBu

A/D CONVERSION

Bit Depth:

24 bits

Sample Rate:

48 kHz

Dynamic Range:

> 110 dB

Frequency Response:

20 – 20kHz, +0 / -1 dB

Crosstalk:

< -60 dB over full bandwidth

ANALOG OUTPUTS

Connectors:

1/4” phone jack unbalanced (hum-canceling), XLR balanced (for main output)

Impedance:

600 ohm

Max Output Level:

+20 dBu

Dynamic Range:

> 110 dB

Frequency Response:

20 – 20kHz, +0 / -1 dB

Crosstalk:

< -60 dB over full bandwidth

DIGITAL I/O

Connectors:

RCA Coaxial Type for S/PDIF I/O, XLR for AES I/O

Format:

S/PDIF – 24 bit

Sample Rate:

48 kHz fixed

USB Audio Clock

48 kHz fixed

MIDI INTERFACE

Input Connector:

7-pin DIN (pins 6 & 7 connected to phantom power in jack)

Out Connector:

5-pin DIN

Thru Connector:

5-pin DIN

PEDAL INTERFACE

Connectors:

× 1/4” TRS phone jack

Format:

Switch: Momentary or Latching; Pedal: 10–100kΩ max, linear taper expression type.

FASLINK™ INTERFACE

Connectors:

× XLR Female

WARNING: Connect ONLY to MFC-101 FASLINK connector or XA-2 FASLINK Adapter.

MFC INTERFACE:

Connector:

RJ-45 Ethernet/EtherCON

IMPORTANT: Do NOT connect to a computer or router/switch/hub!
This jack is only intended for connection to an MFC MIDI Foot Controller.

PHANTOM POWER:

Connector:

Female 2.5mm jack

WARNING: Do NOT connect adapters with a rating higher than 1A (1000ma)

GENERAL

Finish:

Powder coated steel chassis with anodized aluminum faceplate

Display:

160x80 dot matrix graphic LCD

Dimensions:

19” × 3.5” × 14.25” (483 × 88 × 362 mm)

Weight:

14.75 lbs (6.7 kg)

Input Voltage:

100–240 VAC, 47 – 63 Hz (universal input)

Power Consumption:

<40 W

Backup Battery Life:

>10 years

Backup Battery Type:

CR-2032

ENVIRONMENTAL

Operating Temperature:

32 to 122 °F (0 to 50 °C)

Storage Temperature:

-22 to 167 °F (-30 to 70 °C)

Humidity:

Max. 90% non-condensing

Содержание Axe-Fx




















































































































































































































Результаты поиска

Содержание Axe-Fx

Отзывы:

Похожие инструкции для Axe-Fx

Бренды по названию

Популярные бренды

Fractal Axe-Fx, Руководство пользователя

Результаты поиска

Содержание Axe-Fx

Отзывы:

Похожие инструкции для Axe-Fx

Бренды по названию

Популярные бренды