background image

APPENDIX 

192 

 

Doc Q7.0

 

 

Axe-Fx II Bank & Preset Numbers Table 

16.18

The following table shows the BANK SELECT and PROGRAM CHANGE commands needed to recall an Axe-Fx II preset via MIDI. 
DISPLAY OFFSET (p

150

has the potential to add +1 to all of the preset numbers (non-bold). Remember that any Bank Select 

message 

stays in effect

 until a new one is received of the Axe-FxII is rebooted. The Axe-Fx II Mark II has only three preset banks. 

PC # 

BANK A 

BANK B 

BANK C 

BANK D* 

BANK E* 

BANK F* 

 

PC# 

BANK A 

BANK B 

BANK C 

BANK D * 

BANK E * 

BANK F * 

(CC#0 = 0) 

(CC#0 = 1) 

(CC#0 = 2) 

(CC#0 = 3) 

(CC#0 = 4) 

(CC#0 = 5) 

(CC#0 = 0) 

(CC#0 = 1) 

(CC#0 = 2) 

(CC#0 = 3) 

(CC#0 = 4) 

(CC#0 = 5) 

128 

256 

384 

512 

640 

 

64 

64 

192 

256 

448 

576 

704 

129 

257 

385 

513 

641 

 

65 

65 

193 

257 

449 

577 

705 

130 

258 

386 

514 

642 

 

66 

66 

194 

258 

450 

578 

706 

131 

259 

387 

515 

643 

 

67 

67 

195 

259 

451 

579 

707 

132 

260 

388 

516 

644 

 

68 

68 

196 

260 

452 

580 

708 

133 

261 

389 

517 

645 

 

69 

69 

197 

261 

453 

581 

709 

134 

262 

390 

518 

646 

 

70 

70 

198 

262 

454 

582 

710 

135 

263 

391 

519 

647 

 

71 

71 

199 

263 

455 

583 

711 

136 

264 

392 

520 

648 

 

72 

72 

200 

264 

456 

584 

712 

137 

265 

393 

521 

649 

 

73 

73 

201 

265 

457 

585 

713 

10 

10 

138 

266 

394 

522 

650 

 

74 

74 

202 

266 

458 

586 

714 

11 

11 

139 

267 

395 

523 

651 

 

75 

75 

203 

267 

459 

587 

715 

12 

12 

140 

268 

396 

524 

652 

 

76 

76 

204 

268 

460 

588 

716 

13 

13 

141 

269 

397 

525 

653 

 

77 

77 

205 

269 

461 

589 

717 

14 

14 

142 

270 

398 

526 

654 

 

78 

78 

206 

270 

462 

590 

718 

15 

15 

143 

271 

399 

527 

655 

 

79 

79 

207 

271 

463 

591 

719 

16 

16 

144 

272 

400 

528 

656 

 

80 

80 

208 

272 

464 

592 

720 

17 

17 

145 

273 

401 

529 

657 

 

81 

81 

209 

273 

465 

593 

721 

18 

18 

146 

274 

402 

530 

658 

 

82 

82 

210 

274 

466 

594 

722 

19 

19 

147 

275 

403 

531 

659 

 

83 

83 

211 

275 

467 

595 

723 

20 

20 

148 

276 

404 

532 

660 

 

84 

84 

212 

276 

468 

596 

724 

21 

21 

149 

277 

405 

533 

661 

 

85 

85 

213 

277 

469 

597 

725 

22 

22 

150 

278 

406 

534 

662 

 

86 

86 

214 

278 

470 

598 

726 

23 

23 

151 

279 

407 

535 

663 

 

87 

87 

215 

279 

471 

599 

727 

24 

24 

152 

280 

408 

536 

664 

 

88 

88 

216 

280 

472 

600 

728 

25 

25 

153 

281 

409 

537 

665 

 

89 

89 

217 

281 

473 

601 

729 

26 

26 

154 

282 

410 

538 

666 

 

90 

90 

218 

282 

474 

602 

730 

27 

27 

155 

283 

411 

539 

667 

 

91 

91 

219 

283 

475 

603 

731 

28 

28 

156 

284 

412 

540 

668 

 

92 

92 

220 

284 

476 

604 

732 

29 

29 

157 

285 

413 

541 

669 

 

93 

93 

221 

285 

477 

605 

733 

30 

30 

158 

286 

414 

542 

670 

 

94 

94 

222 

286 

478 

606 

734 

31 

31 

159 

287 

415 

543 

671 

 

95 

95 

223 

287 

479 

607 

735 

32 

32 

160 

288 

416 

544 

672 

 

96 

96 

224 

288 

480 

608 

736 

33 

33 

161 

289 

417 

545 

673 

 

97 

97 

225 

289 

481 

609 

737 

34 

34 

162 

290 

418 

546 

674 

 

98 

98 

226 

290 

482 

610 

738 

35 

35 

163 

291 

419 

547 

675 

 

99 

99 

227 

291 

483 

611 

739 

36 

36 

164 

292 

420 

548 

676 

 

100 

100 

228 

292 

484 

612 

740 

37 

37 

165 

293 

421 

549 

677 

 

101 

101 

229 

293 

485 

613 

741 

38 

38 

166 

294 

422 

550 

678 

 

102 

102 

230 

294 

486 

614 

742 

39 

39 

167 

295 

423 

551 

679 

 

103 

103 

231 

295 

487 

615 

743 

40 

40 

168 

296 

424 

552 

680 

 

104 

104 

232 

296 

488 

616 

744 

41 

41 

169 

297 

425 

553 

681 

 

105 

105 

233 

297 

489 

617 

745 

42 

42 

170 

298 

426 

554 

682 

 

106 

106 

234 

298 

490 

618 

746 

43 

43 

171 

299 

427 

555 

683 

 

107 

107 

235 

299 

491 

619 

747 

44 

44 

172 

300 

428 

556 

684 

 

108 

108 

236 

300 

492 

620 

748 

45 

45 

173 

301 

429 

557 

685 

 

109 

109 

237 

301 

493 

621 

749 

46 

46 

174 

302 

430 

558 

686 

 

110 

110 

238 

302 

494 

622 

750 

47 

47 

175 

303 

431 

559 

687 

 

111 

111 

239 

303 

495 

623 

751 

48 

48 

176 

304 

432 

560 

688 

 

112 

112 

240 

304 

496 

624 

752 

49 

49 

177 

305 

433 

561 

689 

 

113 

113 

241 

305 

497 

625 

753 

50 

50 

178 

306 

434 

562 

690 

 

114 

114 

242 

306 

498 

626 

754 

51 

51 

179 

307 

435 

563 

691 

 

115 

115 

243 

307 

499 

627 

755 

52 

52 

180 

308 

436 

564 

692 

 

116 

116 

244 

308 

500 

628 

756 

53 

53 

181 

309 

437 

565 

693 

 

117 

117 

245 

309 

501 

629 

757 

54 

54 

182 

310 

438 

566 

694 

 

118 

118 

246 

310 

502 

630 

758 

55 

55 

183 

311 

439 

567 

695 

 

119 

119 

247 

311 

503 

631 

759 

56 

56 

184 

312 

440 

568 

696 

 

120 

120 

248 

312 

504 

632 

760 

57 

57 

185 

313 

441 

569 

697 

 

121 

121 

249 

313 

505 

633 

761 

58 

58 

186 

314 

442 

570 

698 

 

122 

122 

250 

314 

506 

634 

762 

59 

59 

187 

315 

443 

571 

699 

 

123 

123 

251 

315 

507 

635 

763 

60 

60 

188 

316 

444 

572 

700 

 

124 

124 

252 

316 

508 

636 

764 

61 

61 

189 

317 

445 

573 

701 

 

125 

125 

253 

317 

509 

637 

765 

62 

62 

190 

318 

446 

574 

702 

 

126 

126 

254 

318 

510 

638 

766 

63 

63 

191 

319 

447 

575 

703 

  

127 

127 

255 

319 

511 

639 

768 

Содержание Axe-Fx




















































































































































































































Отзывы: