Fraco SEP-5000, Руководство пользователя

Страница: 14 / 89

Transport platform SEP Serie
SEP u
ser’s manual Page 14 of 89
Doc no. RD-7243-MA-001-02
4. Technical data
4.1. General data
FRACO GENERAL DATA - SEP
Technical
Nominal speed (vertical travel) 0-40 ft/min (0-12,2 m/min)
Speed governor activation speed (centrifugal
brake)
85 ft/min (26 m/min)
MAXIMUM number of persons on the platform 13 persons (Equally distributed)
Mast section type Single rack
(13090104)
26" x 26" x 5'-0"
(650 mm x 650 mm x 1,5 m)
Double rack
(13090137)
26" x 26" x 5'-0"
(650 mm x 650 mm x 1,5 m)
Mast section weight 300 lb (136 kg) 305 lb (138 kg)
Mast section height 5'-0" (1,5 m)
* MAXIMUM freestanding installation height
(without anchor)
* With adjustable legs: Prohibited!
MAXIMUM installation height (anchored) 1 300 ft (400 m)
** MAXIMUM first anchor installation height ** With adjustable leg 20 ft (6,0 m)
MAXIMUM height over the last anchor (highest
anchor)
During operation : 0 ft (0 m) MAX from the platform floor to the
last anchor.
During installation : 0 ft (0 m) MAX from the top of the
protection roof to the last anchor (highest anchor).
*** "Typical" spacing between anchors *** 30 ft (9,0 m)
MIN 20 ft (6,0 m)
MAX 40 ft (12,0 m)
Spacing between cable guides MAX 20 ft (6,0 m)
Pay load MAXIMUM (Capacity)
Important! Deduce the average load of workers
and their personal equipment.
∞
S
EE SECTION
O
PERATION SAFETY INSTRUCTIONS
,
ON PAGE
41.
Depending on model
5 000 lb (2 270 kg)
6 000 lb (2 720 kg)
7 000 lb (3 175 kg)
8 000 lb (3 630 kg)
MAXIMUM load during installation, assembly and
disassembly.
Depending on model
Operation temperature Do not operate below -4°F (-20°C).
Note: it is recommended to use the permanent heating system if
the platform is used in a [41°F (5°C) à -4°F (-20°C)] environment
REFER TO SECTION
5.5 E
LECTRICAL CONNECTION
(
ON SITE
),
ON
PAGE
37.
MAXIMUM dynamic speed of the wind
During installation (assembly/disassembly) 28 mi/h (45 km/h)
Freestanding 28 mi/h (45 km/h)
In service 35 mi/h (55 km/h)
Out of service Refer to local regulation in effect
Electrical characteristics
Power outage Specific to each unit
(See identification pate and engineering package specific to the
project for electrical data)
∞
S
EE SECTION
12.1 E
LECTRICAL TECHNICAL DATA
,
ON PAGE
79.
Energy consumption
VFC
Disk traction force
Table 2
– General data
* Base with adjustable jack legs : freestanding use/installation is forbidden at all time. The mast must be supported with
a crane or an independent lifting system for the installation of the first two (2) anchors.
** Base with
adjustable jack legs : the first anchor must be put in place within the 20'-0" (6m) from the ground. Install the
subsequent anchors at "typical" spacing from one another. See
« *** »
bellow.
*** The typical spacing between anchors is 30'-0" (9 m) ± 10'-0" (3 m), however it is forbidden to install two (2)
subsequent anchors with more than a 10'-0" (3 m) difference compared to the two next/previous anchors set.
Valid example : (anchors 1-2 = distance of 25'-0" (7,5 m) and anchors 2-3 = distance of 35'-0" (10,5 m)).
Invalid example :(anchors 1-2 = distance of 25'-0" (7,5 m) and anchors 2-3 = distance of 40'-0" (12 m)).