FPI Regency P36D-LP1 Скачать руководство пользователя страница 21

Страница: 21 / 76

FPI P36D-1 Zero Clearance Direct Vent Gas Fireplace

EXTERIOR VENT TERMINATION LOCATIONS

Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm)

Clearance to window or door that may be opened *(12"/30cm)

Clearance to permanently closed window *(min. 12"/30cm)

ertical clearance to ventilated sofﬁ

t located above the terminal within a horizontal

distance of (24"/60cm) from the centerline of the terminal (min. 18"/46cm) check with

local code.

Clearance to unventilated sofﬁ

(min.

15"/38cm)

Clearance to outside corner: with

AstroCap

rmination Cap (min. 6"/15cm), with

Dura-V

ent

rmination Cap (14"/36cm)

Clearance to inside corner: with

AstroCap

rmination Cap (min. 6"/15cm), with Dura-

ent

rmination Cap (12"/30cm)

Not to be installed above a meter/regulator assembly within (3'/90cm) horizontally

from the centerline of the regulator

Clearance to service regulator vent outlet *(min. 36"/90cm)

Clearance to non-mechanical air supply inlet to building or the combustion air inlet to

any other appliance *(12"/30cm)

Clearance to a mechanical air supply inlet *(min. 72"/1.8m)

Clearance above paved sidewalk or a paved driveway located on public property

*(min. 84"/2.1m)

Clearance under veranda, porch, deck, or balcony *(min. 12"/30cm)

Note:

vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings a

nd serves both dwellings.

- Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂ

oor

- If the vent termination is accessible, a certiﬁ

ed guard shall be installed.

As speciﬁ

ed in CGA

B149 Installation Code. Note: Local codes or regulations may require dif

ferent clearances.

INSTALLATION

Содержание Regency P36D-LP1













































































Результаты поиска

Содержание Regency P36D-LP1

Отзывы:

Похожие инструкции для Regency P36D-LP1

Бренды по названию

Популярные бренды

FPI Regency P36D-LP1, Инструкция для владельца и по установке

Результаты поиска

Содержание Regency P36D-LP1

Отзывы:

Похожие инструкции для Regency P36D-LP1

Бренды по названию

Популярные бренды