Four-Faith F2816 V2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

background image

Page 11 of 56

Cellular

Module

MCU

Antenna

SIM/UIM

Interface

Indicator

Lights

SRAM&

FLASH

WDT Module

User Interface

RS232/RS485/RS422

Module

Power Module

Figure1-2 IP Modem principle chart

F2x16 consists of the following major components:

- A controlling unit made of a CPU (industrial 32-bit processor)
- WDT module
- Cellular module
- RS232/RS485 serial module
and the following physical Interfaces
- 1 x Power supply (+/-)
- 3 x LED indicators (ACT/Online/Power)
- 1 x RS232 port (RX, TX, GND) and 1xRS485 port(A,B)
-

2 x DI/DO + 1 x ADC (DI/DO can be customized to pulse c ounting)

The working principle is the following

After power on, the CPU controlling system functions will communicate with serial modules, it

will send AT commands to cellular wireless module and the wireless module will dial up to

connect to public internet. After device Dial up, online led will turn on, and F2x16 will provide

data transmission for serial devices connected to the switch module and the devices conected to

GPIO interface.

Any configuration is set using the user interface module which can also access to the power

module powering the unit. Power Interface has a standard 3.5mm terminal block interface and

built in phase reversal and over voltage protection, while SIM/UIM standard SIM card slots

support 1.8V/3V SIM/UIM cards and have built in 15KV ESD. This together with its casing

grants good immunity to power spikes, installation mistakes and e.m. discharge, for the safety of

users.

Modems can be set either using AT command or configuration software provided with the modem.

«
...
9
10
11
12
13
...
»

Содержание F2816 V2

























































Отзывы:

Нет отзывов

Похожие инструкции для F2816 V2

Бренд: M/A-Com Страницы: 22

Бренд: Javad Страницы: 7

DSL-302G - 8 Mbps DSL Modem

Бренд: D-Link Страницы: 11

Бренд: Sprint Страницы: 78

Бренд: Conceptronic Страницы: 81

Бренд: EpiCom Страницы: 25

Бренд: Swann Страницы: 2

Бренд: Exede Страницы: 4

Бренд: Belkin Страницы: 2

Бренд: Zoom Страницы: 4

Бренд: Zoom Страницы: 3

Бренд: Zoom Страницы: 44

Бренд: Enfora Страницы: 28

Бренд: Enfora Страницы: 27

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 29

Бренд: Flash Страницы: 2

Бренд: NETGEAR Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды