17
DE-1 Owner’s Manual
SINGLE
DUAL
MODE
TYPE
DELAY
PITCH
FLANGE
VOCAL
L.HALL
ROOM
DLY+REV
S.HALL
PLATE
MISC
CHO
1
VARIATION
5
1
1
7
3
6
2
4
10
8
9
ADJUST
PARAM.1
ADJUST
PARAM.2
MIX
EFF
DRY
DRY+EFF
PARAM.3
MIX
EFF
DRY
DRY+EFF
_
+
PARAM.3
POWER
ADJUST
MIX
PARAM.2
1
TYPE
VARIATION
DELAY
PITCH
FLANGE
PEAK
VOCAL
L.HALL
ROOM
DLY+REV
S.HALL
PLATE
MISC
CHO
5
1
1
7
3
6
2
4
10
8
9
1
TYPE
VARIATION
DELAY
PITCH
FLANGE
PEAK
ADJUST
VOCAL
L.HALL
ROOM
MIX
EFF
DRY
SINGLE
DUAL
MODE
PARAM.1
DLY+REV
S.HALL
PLATE
MISC
CHO
5
1
1
7
3
6
2
4
10
8
9
EFF
DRY
DRY+EFF
DRY+EFF
EFFECT 2
EFFECT 1
_
+
Select the “DUAL” on the
MODE SW.
Choose the Effect Type you
want to set for the Effect 1 and
Effect 2. See page 5 for the
variety of Effect Types.
Set the variation on the Effect
Type that you have chosen.
Adjust the parameters for
Effect 1 and Effect 2.
Adjust the mixing balance of
the Dry sound and Effect sound
to get the ratio you require from
the OUTPUT 1 and OUTPUT
2 jack sockets.
<Caution on Effect Processing>
The PEAK LED indicator on the front panel is designed so
that it will illuminate when the Input signal reaches 6dB below
the distortion level. First, adjust the Input level using the
control knob and watch the LED indicator. The best level
setting makes the PEAK LED illuminate occasionally. In the
case of the sound being distorted in the internal DSP, in
spite of no indications on the PEAK LED, this is due to the
rise of the entire signal level due to a variety of Effect sounds
being used. If this happens, reduce the Input level with the
control knob so that the Output sound is not distorted.
<Caution on changing SW position>
The Output signal will disappear momentarily when you
change the position of the MODE SW, EFFECT TYPE SW
and VARIATION SW. This is not a fault. It is due to the DE-
1 resetting its internal DSP.
<Caution when using the ADJUST knob and MIX knob>
Some clicking noises may be heard when you control the
ADJUST knob and MIX knob, with certain types and sounds
of the Effect.
The ADJUST knob may not give you functions even if you
try to increase the parameter when the default setting is
already at the maximum. Similarly, you cannot decrease it
further if the default parameter setting is already at the
minimum position.
How to use the Single Mode
Here, we discuss the practical operation of the Single Mode. The Single Mode has the features listed
below.
[Outstanding features of the Single Mode]
1. You can use it as a high quality single channel Effect Processor.
2. It provides stereo Inputs and Outputs.
3. It has three ADJUST knobs as PARAM. 1~3. With these, you can alter three individual parameter settings
in more detail, on top of the typical presets designed for each Effect.
4. It offers a higher density reverb than the Dual Mode.
5. The independent channel algorithm offers completely separate Output signals for each channel (L,R).
This is an example of the “Single Mode” used
in a live performance. Connect the stereo output
of the Keyboard directly into the DE-1 Input
jack sockets. Connect the Effect Output of the
DE-1 into the two separate PA speakers. Also
you can operate the Effect Mute ON/OFF
remotely via a Foot SW such as Fostex Model
8051.
5
4
3
2
1