Foshk WH0202 Скачать руководство пользователя страница 2

 

 

1) Remove Rain Gauge cover            2) Remove the battery cover

 

 

 

 

3) Observing the correct polarization insert 2 “AAA” Alkaline 
Batteries into the compartment and replace the cover.

 

 

 
 
 
 
 
 
 
 
 
 

 

 

Note: when opening the battery cover make sure that the batteries 
do not spring free from the contacts since this will cause start and 
transmisison problem 

 
 

 

- 2 -

 

 

Indoor receiver battery installs 

1) 

Insert two AA batteries into the indoor receiver. When the base 
station is powered up, a short beep will sound and all LCD 
segments will light up for about 4 seconds before it enters into 
learning mode to learn the sensors security code.

 

Every time the 

remote sensor is powered up (for example after a change of 
batteries), a random security code is transmitted and this code 
must be synchronized with the base station to receive weather 
data. 

Thus if battery change happened on remote sensor side, 

then the base station must be power up again to re-learn the 
transmitter.

 

2) 

   Do not press any keys for 10 minutes 

 

3) 

The receiver will start to search time signal. If there is no time 
signal found within 70s, the unit will turn off the receiver. If there is 
time signal received, then the clock will have the radio controlled 
time icon flashing indicating that the clock is in the time reception 
progress. Normally within 10 minutes the clock should have the 
correct time displayed. 

4) 

If no time reception is possible, then manually set the time. The 
clock will try to make radio controlled time reception every hour. 
When radio controlled time is received, the radio controlled time 
icon will be turned on.  

5) 

If your time zone is not at UTC+1:00, then manually set the time 
zone so that your clock time will be updated correctly after radio 
controlled time is received. 

6) 

If the clock can’t have radio controlled time received after 24 
hours, then try to put the clock in a place near window. The clock 
should not be placed on metal table or near monitor.   

 

Note for Radio Controlled Time: 

The time and date display is based on the signal provided by the highly 
accurate government operated atomic clock. The base station will 
continue to scan for the radio controlled time signal each day at 2:00, 
8:00, 14:00 and 20:00 despite it being manually set. If reception has 
been unsuccessful, then the radio controlled time icon will not appear 
but reception will still be attempted continually. If reception has been 
successful, the received time and date will overwrite the manually set 
time and date.  

 

Note: 

 

Please participate in the preservation of the environment by 
properly disposing of all used-up batteries and accumulators at 
designated disposal points. Never dispose of batteries in a fire as 
this may cause explosion, risk of fire or leakage of dangerous 
chemicals and fumes 

 

 

 

- 3 -

 Mounting 

Base Station

With one foldable legs at the back of the unit, the base station can be 
placed onto any flat surface or wall mounted at the desired location by 
the hanging holes at the back of the unit. It is important to check that the 
radio signal can be received before permanently mounting any of the 
units 

 Remote Sensor 

Place the rain gauge in an appropriate location. The rain gauge has a 
range of 100meters. Keep in mind that  100 meters RF reception 
distance is for condition in open air with no obstructions, and rain 
gauge transmitter sitting one meter above ground. Real-world 
transmission range will vary depending on what is in the path of the 
signal. Each obstruction (roof, walls, floors, ceilings, thick trees, etc.) 
will effectively cut signal range.  

There is a NTC type temperature sensor inside the rain box,. Under 

direct sunshine condition, the temperature reading can be 3-4 

degrees higher than real outdoor temperature. In order to get real 

correct outdoor temperature, it is recommended to install the sensor 

in north faced places or where there is no long time exposing to direct 

sun light. 

 
Program mode 
The base station has two key for easy operation: 

RAIN

 key and 

SET

 

key. And there are two program modes available: Rain Mode and 
setting mode 
 
The setting mode will return to normal display mode while key idle 30s. 

 

RAIN Mode 

 While in normal mode, press 

RAIN 

key, 1hour rainfall record will be 

displayed. Press 

RAIN

 key again, 24hour rainfall record will be 

displayed. Press 

RAIN

 key the third time, week rainfall record will be 

displayed.  Press 

RAIN

 Key the fourth time, TOTAL rainfall record will 

be displayed. 
 

Reset Rain Data  

Press 

RAIN 

key for approx 2 seconds at 1hour rainfall mode, 1hour 

rainfall record will be reset to 0. Press 

RAIN 

key for approx 2 seconds at 

24hour rainfall mode, 1hour and 24hour rainfall record will be reset to 0. 
Press 

RAIN 

key for approx 2 seconds at week rainfall mode, 1hour, 

- 4 -

Отзывы: